- 您现在的位置：买卖IC网 > PDF目录1916 > DS80C410-FNY+ (Maxim Integrated Products)IC MCU 75MHZ 16MB HP 100-LQFP PDF资料下载
参数资料
| 型号： | DS80C410-FNY+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 87/102页 |
| 文件大小： | 0K |
| 描述： | IC MCU 75MHZ 16MB HP 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 系列： | 80C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 75MHz |
| 连通性： | 1 线，CAN，EBI/EMI，以太网，SIO，UART/USART |
| 外围设备： | 电源故障复位，WDT |
| 输入/输出数： | 64 |
| 程序存储器容量： | 64KB（64K x 8） |
| 程序存储器类型： | ROM |
| RAM 容量： | 64K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页当前第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
85 of 102
Task Scheduler
The DS80C410 ROM firmware implements a priority based preemptive task scheduler. Each task created is
represented in a task ring by a corresponding task control block (TCB). The TCB holds critical information specific
to the task, such as the ID, priority, event bit mask, wake-up time, and pointers to state information and next task.
Using a timer, the scheduler is run approximately every 4ms (at 18.432MHz crystal frequency) unless deferred
because another interrupt is in progress. The scheduler supports an unlimited number of tasks and allows addition,
deletion, or modification on the fly. However, one should realize that increasing the number of tasks increases the
time needed by the scheduler to search and prioritize the ring. The High-Speed Microcontroller User’s Guide:
Network Microcontroller Supplement provides greater detail about the task scheduler and its functionality.
Controller Area Network (CAN) Module
The DS80C410 incorporates one CAN controller that is fully compliant with the CAN 2.0B specification. On the
DS80C411, the CAN controller is not available. CAN is a highly robust, high-performance communication protocol
for serial communications. Popular in a wide range of applications including automotive, medical, heating,
ventilation, and industrial control, the CAN architecture allows for the construction of sophisticated networks with a
minimum of external hardware.
The CAN controller supports the use of 11-bit standard or 29-bit extended acceptance identifiers for up to 15
messages, with the standard 8-Byte data field, in each message. Fourteen of the 15 message centers are
programmable in either transmit or receive modes, with the 15th designated as an FIFO-buffered, receive-only
message center to help prevent data overruns. All message centers have two separate 8-bit media masks and
media arbitration fields for incoming message verification. This feature supports the use of higher-level protocols
that use the first and/or second byte of data as a part of the acceptance layer for storing incoming messages. Each
message center can also be programmed independently to test incoming data with or without the use of the global
masks.
Global controls and status registers in the CAN unit allow the microcontroller to evaluate error messages, generate
interrupts, locate and validate new data, establish the CAN bus timing, establish identification mask bits, and verify
the source of individual messages. Each message center is individually equipped with the necessary status and
control bits to establish direction, identification mode (standard or extended), data field size, data status, automatic
remote frame request and acknowledgment, and perform masked or nonmasked identification-acceptance testing.
Communicating with the CAN Module
The microcontroller interface to the CAN modules is divided into two groups of registers. All the global CAN status
and control bits as well as the individual message center control/status registers are located in the SFR map. The
remaining registers associated with the message centers (data identification, identification/arbitration masks, format
and data) are located in MOVX data space. For the DS80C410, the message centers are fixed from FFDB00h –
FFDBFFh. The internal architecture of the DS80C410 requires that the device be in one of the two 24-bit
addressing modes when the CMA bit is set to correctly access the CAN MOVX memory. A special lockout feature
prevents the accidental software corruption of the control, status, and mask registers while a CAN operation is in
progress. Each CAN controller uses a total of 15 message centers. Each message center is composed of four
specific areas that include the following:
1) Four arbitration registers (C0MxAR0-3) that store either the 11-bit or 29-bit arbitration value. These registers
are located in the MOVX memory map.
2) A format register (C0MxF) that informs the CAN controller as to the direction (transmit or receive), the number
of data bytes in the message, the identification format (standard or extended), and the optional use of the
identification mask or media mask during message evaluation. This register is located in the MOVX memory
map.
3) Eight data bytes for storage of 0 to 8 Bytes of data (C0MxD0–7) are located in the MOVX memory map.
4) Message control registers (C0MxC) are located in the SFR memory for fast access.
Each of the message centers is identical with the exception of message center 15. Message center 15 has been
designed as a receive-only center and is also buffered through the use of a two-message FIFO to help prevent
message loss in a message-overrun situation. The receipt of a third message before either of the first two are read
overwrites the second message, leaving the first message undisturbed.
相关PDF资料 |
PDF描述 |
|---|---|
| DS8102+ | IC MODULATOR/DECODER 16-TSSOP |
| DS8113-JNG+ | IC INTERFACE SMART CARD 28-TSSOP |
| DS8313-RRX+ | IC INTERFACE SMART CARD 28-SOIC |
| DS8500-JND+T&R | IC MODEM HART SGL 3.6V 20-TQFN |
| DS87C520-ENL | IC MCU EPROM/ROM 33MH IND 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS80C410-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C411 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Network Microcontrollers with Ethernet and CAN |
| DS80C411-FNY | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C411-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80CH11 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:System Energy Manager |
发布紧急采购，3分钟左右您将得到回复。