- 您现在的位置：买卖IC网 > PDF目录1916 > DS80C410-FNY+ (Maxim Integrated Products)IC MCU 75MHZ 16MB HP 100-LQFP PDF资料下载
参数资料
| 型号： | DS80C410-FNY+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 91/102页 |
| 文件大小： | 0K |
| 描述： | IC MCU 75MHZ 16MB HP 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 系列： | 80C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 75MHz |
| 连通性： | 1 线，CAN，EBI/EMI，以太网，SIO，UART/USART |
| 外围设备： | 电源故障复位，WDT |
| 输入/输出数： | 64 |
| 程序存储器容量： | 64KB（64K x 8） |
| 程序存储器类型： | ROM |
| RAM 容量： | 64K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页当前第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
89 of 102
Error Counter Interrupt Generation
The CAN module can be configured to alert the microcontroller when either 96 or 128 errors have been detected by
the transmit or receive error counters. The error-count select bit, ERCS (C0C.1), selects whether the limit is 96
(ERCS = 0) or 128 (ERCS = 1) errors. When the error limit is exceeded, the CAN error-count exceeded bit CECE
(C0S.6) is set. If the ERIE, C0IE, and EA SFR bits are configured, an interrupt is generated. If the ERCS bit is set,
the device generates an interrupt when the CECE bit is set or cleared, if the interrupt is enabled.
Bit Timing
Bit timing of the CAN transmission can be adjusted per the CAN 2.0B specification. The CAN 0 bus timing register
zero (C0BT0), located in the control/status/mask register block in MOVX memory, controls the PHASE_SEG1 and
PHASE_SEG2 time segments and the baud rate prescaler (BPR5–BPR0). The CAN 0 bus timing register one
(C0BT1) contains the controls for the sampling rate and the number of clock cycles assigned to the Phase
Segment 1 and 2 portions of the nominal bit time. The values of both of the bus timing registers are automatically
loaded into the CAN controller following each software change of the SWINT bit from a 1 to a 0 by the
microcontroller. The bit timing parameters must be set before starting operation of the CAN controller. These
registers are modifiable only during a software initialization, (SWINT = 1), when the CAN controller is not in a bus-
off mode, and after the removal of a system reset or a CAN reset. To avoid unpredictable behavior of the CAN
controller, the software cannot clear the SWINT bit when TSEG1 and TSEG2 are both cleared to 0.
1-Wire Bus Master
The DS80C410 incorporates a 1-Wire bus master to support communication to external 1-Wire devices. The bus
master provides complete control of the 1-Wire bus and coordinates transmit (Tx)/receive (Rx) activities with
minimal supervision by the CPU. All timing and control sequences for the bus are generated within the bus master.
Communication between the CPU and the bus master is accomplished through read/write access of the 1-Wire
master address (OWMAD; EEh) and 1-Wire master data (OWMDR; EFh) SFRs. When 1-Wire bus activity
generates a condition that requires servicing by the CPU, the bus master sets the appropriate status bit to create
an interrupt request to the CPU. If the 1-Wire bus master interrupt source has been enabled, the CPU services the
request according to the priority that has been assigned. The 1-Wire bus master supports bit banging, search ROM
accelerator, and overdrive modes. Detailed operation of the 1-Wire bus is described in The Book of iButton
Standards (www.maxim-ic.com/iButtonBook).
Communicating with the Bus Master
The microcontroller interface to the 1-Wire bus master is through two SFRs, 1-Wire master address (OWMAD;
EEh), and 1-Wire master data (OWMDR; EFh). These two registers allow read/write access of the six internal
registers of the 1-Wire bus master. The internal registers provide a means for the CPU to configure and control
transmit/receive activity through the bus master.
The three least significant bits (A2:A0) of the OWMAD SFR specify the address of the internal register to be
accessed. The OWMDR SFR is used for read/write access to the implemented bits of the specified internal
register. All internal registers are read/write accessible except the interrupt flag register (xxxxx010b), which allows
only read access to interrupt status flags. It should also be noted that all writes to the Tx/Rx buffer register
(xxxxx001b) are directed to the Tx buffer and all reads retrieve data from the Rx buffer. The 1-Wire bus master
internal register map is shown in Table 20.
Table 20. 1-Wire Bus Master Internal Register Map
REGISTER ADDRESS*/
FUNCTION
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
000
Command
—
OW_IN
FOW
SRA
1WR
001
Tx/Rx Buffer
D7
D6
D5
D4
D3
D2
D1
D0
010
Interrupt Flag
OW_LOW
OW_SHORT
RSRF
RBF
TEMT
TBE
PDR
PD
011
Interrupt Enable
EOWL
EOWSH
ERSF
ERBF
ETMT
ETBE
—
EPD
100
Clock Divisor
CLK_EN
—
DIV2
DIV1
DIV0
PRE1 PRE0
101
Control
EOWMI
OD
BIT_CTL
STP_SPLY
STPEN
EN_FOW
PPM
LLM
*Logic states represented by A2:A0 other than those listed in the table are considered to be invalid addresses and are not supported by the bus
master. When OWMAD contains an invalid address, reads of OWMDR return invalid data, and writes to OWMDR do not change the internal
register contents.
相关PDF资料 |
PDF描述 |
|---|---|
| DS8102+ | IC MODULATOR/DECODER 16-TSSOP |
| DS8113-JNG+ | IC INTERFACE SMART CARD 28-TSSOP |
| DS8313-RRX+ | IC INTERFACE SMART CARD 28-SOIC |
| DS8500-JND+T&R | IC MODEM HART SGL 3.6V 20-TQFN |
| DS87C520-ENL | IC MCU EPROM/ROM 33MH IND 44TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS80C410-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C411 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Network Microcontrollers with Ethernet and CAN |
| DS80C411-FNY | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80C411-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS80CH11 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:System Energy Manager |
发布紧急采购，3分钟左右您将得到回复。