参数资料
| 型号： | EPF6024ATC144-3N |
| 厂商： | Altera |
| 文件页数： | 9/52页 |
| 文件大小： | 0K |
| 描述： | IC FLEX 6000 FPGA 24K 144-TQFP |
| 产品培训模块： | Three Reasons to Use FPGA's in Industrial Designs |
| 标准包装： | 180 |
| 系列： | FLEX 6000 |
| LAB/CLB数： | 196 |
| 逻辑元件/单元数： | 1960 |
| 输入/输出数： | 117 |
| 门数： | 24000 |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 工作温度： | -40°C ~ 100°C |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-TQFP（20x20） |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Altera Corporation
17
FLEX 6000 Programmable Logic Device Family Data Sheet
Figure 8. LE Clear & Preset Modes
Asynchronous Clear
The flipflop can be cleared by either LABCTRL1 or LABCTRL2.
Asynchronous Preset
An asynchronous preset is implemented with an asynchronous clear. The
Altera software provides preset control by using the clear and inverting
the input and output of the register. Inversion control is available for the
inputs to both LEs and IOEs. Therefore, this technique can be used when
a register drives logic or drives a pin.
In addition to the two clear and preset modes, FLEX 6000 devices provide
a chip-wide reset pin (DEV_CLRn) that can reset all registers in the device.
The option to use this pin is set in the Altera software before compilation.
The chip-wide reset overrides all other control signals. Any register with
an asynchronous preset will be preset when the chip-wide reset is asserted
because of the inversion technique used to implement the asynchronous
preset.
The Altera software can use a programmable NOT-gate push-back
technique to emulate simultaneous preset and clear or asynchronous load.
However, this technique uses an additional three LEs per register.
FastTrack Interconnect
In the FLEX 6000 OptiFLEX architecture, connections between LEs and
device I/O pins are provided by the FastTrack Interconnect, a series of
continuous horizontal and vertical routing channels that traverse the
device. This global routing structure provides predictable performance,
even for complex designs. In contrast, the segmented routing in FPGAs
requires switch matrices to connect a variable number of routing paths,
increasing the delays between logic resources and reducing performance.
PRN
DQ
labctrl1 or
labctrl2
Asynchronous Clear
Asynchronous Preset
CLRN
DQ
Chip-Wide Reset
labctrl1 or
labctrl2
Chip-Wide Reset
相关PDF资料 |
PDF描述 |
|---|---|
| AT28C256F-15SU | IC EEPROM 256KBIT 150NS 28SOIC |
| EPF6024ATC144-3 | IC FLEX 6000 FPGA 24K 144-TQFP |
| AT28HC256E-12TU | IC EEPROM 256KBIT 120NS 28TSOP |
| AGL400V5-CS196 | IC FPGA 1KB FLASH 400K 196-CSP |
| AT27C4096-55JU | IC OTP 4MBIT 55NS 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPF8001GM | 制造商:PCA 制造商全称:PCA ELECTRONICS INC. 功能描述:10/100 LAN Interface Module with Common Mode Termination |
| EPF8007M | 制造商:PCA 功能描述: |
| EPF8008 | 制造商:PCA 制造商全称:PCA ELECTRONICS INC. 功能描述:High Speed LAN Interface Module |
| EPF8008A | 制造商:PCA 制造商全称:PCA ELECTRONICS INC. 功能描述:High Speed LAN Interface Module |
| EPF8010GH | 制造商:PCA 制造商全称:PCA ELECTRONICS INC. 功能描述:10/100Base-TX Interface Module with Enhanced Common Mode Attenuation |
发布紧急采购，3分钟左右您将得到回复。