参数资料
型号: IBIS4-A-6600
厂商: Cypress Semiconductor Corp.
英文描述: 6.6 MP CMOS Image Sensor
中文描述: 6.6万像素的CMOS图像传感器
文件页数: 20/40页
文件大小: 1698K
代理商: IBIS4-A-6600
IBIS4-A-6600
CYII4SM6600AB
ADVANCE
INFORMATION
Document Number: 001-02366 Rev. *D
Page 20 of 40
Sequencer and Registers
Figure 3. showed a number of control signals that are needed
to operate the sensor in a particular sub-sampling mode, with
a certain integration time, output amplifier gain, etc. Most of
these signals are generated on-chip by the sequencer that
uses only a few control signals. These control signals should
be generated by the external system:
SYS_CLOCK, which defines the pixel rate (nominal 40 MHz),
Y_START pulse, which indicates the start of a new frame,
Y_CLOCK, which selects a new row and will start the row
blanking sequence, including the synchronization and loading
of the X-register.
The relative position of the pulses will be determined by a
number of data bits that are uploaded in internal registers
through a Serial to Parallel interface (SPI).
Internal Registers
Table 15. shows a list of the internal registers with a short
description. In the next section, the registers are explained in
more detail.
Table 15. List of Internal Registers
Register
0 (0000)
Bit
Name
Description
11:0
SEQUENCER register
Selection of mode, granularity of the X sequencer clock, calibration,
Default value <11:0>:"000100000000"
Mode of readout:
NDR = 0: normal readout (double sampling)
NDR = 1: non-destructive readout
4 different modes of non-destructive readout (no influence if NDR = 0)
0 = normal operation
1 = reset of pixels before readout
0 = electronic shutter operation
1 = addressing from both sides
0 = fast
1 = slow
0 = fast
1 = slow
0 = normal mode
1 = 'continuous precharge'
Granularity of the X sequencer clock
0
NDR
1:2
3
NDR_mode
RESET_BLACK
4
FAST_RESET
5
FRAME_CAL_MODE
6
LINE_CAL_MODE
7
CONT_CHARGE
8
9
10
GRAN_X_SEQ_LSB
GRAN_X_SEQ_MSB
BLACK
0 = normal mode
1 = disconnects column amplifiers from busses, output of amplifier equals
dark reference level
0 = normal mode
1 = continuous reset of all pixels
Number of pixels to count (X direction). Max. 2222/2 (2210 real + 12 dummy
pixels). Default value <10:0>:"01000000000"
Number of lines to count (Y direction).
Max. 3014 (3002 real + 12 dummy pixels).
Default value <11:0>:"101111000110"
Integration time.
Default value <11:0>:"000000000001"
Delay of sequencer pulses
Default value <7:0>:"00000011"
Delay of PIX_VALID pulse
Delay of EOL/EOF pulses
X start position (0 to 98).
Default value <6:0>:"0000000"
Y start position (0 to 137).
Default value <7:0>:"00000000"
11
RESET_ALL
1 (0001)
10:0
NROF_PIXELS
2 (0010)
11:0
NROF_LINES
3 (0011)
11:0
INT_TIME
4 (0100)
7:0
DELAY
0:3
4:7
6:0
DELAY_PIX_VALID
DELAY_EOL/EOF
X_REG
5 (0101)
6 (0110)
7:0
Y_REG
[+] Feedback
相关PDF资料
PDF描述
IBM0116160 1M x 16 12/8 DRAM(16M位 动态RAM(带20条地址线,其中12条为行地址选通,8条为列地址选通))
IBM0116160B 1M x 16 12/8 DRAM(16M位 动态RAM(带20条地址线,其中12条为行地址选通,8条为列地址选通))
IBM0116160M 1M x 16 12/8 DRAM(16M位 动态RAM(带20条地址线,其中12条为行地址选通,8条为列地址选通))
IBM0116160P 1M x 16 12/8 DRAM(16M位 动态RAM(带20条地址线,其中12条为行地址选通,8条为列地址选通))
IBM0116165 1M x 16 12/8 EDO DRAM(16M位 动态RAM(超页面模式读写并带20条地址线,其中12条为行地址选通,8条为列地址选通))
相关代理商/技术参数
参数描述
IBIS4-A-6600-C-2 制造商:Cypress Semiconductor 功能描述:IMAGE SENSOR COLOR CMOS 2210X3002PIXELS - Bulk
IBIS4-A-6600-M-2 制造商:Cypress Semiconductor 功能描述:IMAGE SENSOR MONOCHROME CMOS 2210X3002PIXELS - Bulk
IBIS5-A-1300-C-1 制造商:Cypress Semiconductor 功能描述:IMAGE SENSOR COLOR CMOS 1280X1024PIXELS 84PIN LCC - Bulk
IBIS5-A-1300-C-2 制造商:Cypress Semiconductor 功能描述:Image Sensor Color CMOS 1280x1024Pixels 84-Pin LCC 制造商:Cypress Semiconductor 功能描述:IMAGE SENSOR COLOR CMOS 1280X1024PIXELS 84PIN LCC - Bulk
IBIS5-A-1300-M-1 制造商:Cypress Semiconductor 功能描述:Image Sensor Monochrome CMOS 1280x1024Pixels 84-Pin LCC 制造商:Cypress Semiconductor 功能描述:IMAGE SENSOR MONOCHROME CMOS 1280X1024PIXELS 84PIN LCC - Bulk