- 您现在的位置：买卖IC网 > PDF目录15170 > ISL6306IRZ-T (Intersil)IC REG CTRLR BUCK PWM VM 40-QFN PDF资料下载
参数资料
| 型号： | ISL6306IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 22/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 4,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 275kHz |
| 占空比： | 66.7% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISL6306
C REF R REF = T VID
The ISL6306 checks the VID inputs six times every switching
cycle. If the VID code is found to have been changed, the
controller waits for half of a switching cycle before executing a
6.25mV step change. If the difference between DAC level and
the new VID code changes during the half-cycle waiting period,
no change to the DAC output is made. If the VID code is more
than 1 bit higher or lower than the DAC (not recommended),
the controller will execute 6.26mV step change six times per
cycle until VID and DAC are equal. Therefore it is important to
carefully control the rate of VID stepping in 1-bit increments.
In order to ensure the smooth transition of output voltage during
VID change, a VID step change smoothing network, composed
of R REF and C REF , can be used. The selection of R REF is
based on the desired offset voltage as detailed in “Output-
C REF is based on the time duration for 1 bit VID change and
the allowable delay time.
Assuming the microprocessor controls the VID change at 1-bit
every T VID , the relationship between the time constant of R REF
and C REF network and T VID is given by Equation 13.
(EQ. 13)
Operation Initialization
Prior to converter initialization, proper conditions must exist on
the enable inputs and VCC. When the conditions are met, the
controller begins soft-start. Once the output voltage is within the
proper window of operation, VR_RDY asserts logic high.
Enable and Disable
While in shutdown mode, the PWM outputs are held in a
high-impedance state to assure the drivers remain off. The
following input conditions must be met before the ISL6306 is
released from shutdown mode.
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL6306 is guaranteed. Hysteresis between the rising
and falling thresholds assure that once enabled, the
ISL6306 will not inadvertently turn off unless the bias
voltage drops substantially (see “Electrical
Specifications” on page 8).
2. The ISL6306 features an enable input (EN_PWR) for
power sequencing between the controller bias voltage
and another voltage rail. The enable comparator holds
the ISL6306 in shutdown until the voltage at EN_PWR
rises above 0.875V. The enable comparator has about
130mV of hysteresis to prevent bounce. It is important
that the driver ICs reach their POR level before the
ISL6306 becomes enabled. The schematic in Figure 10
demonstrates sequencing the ISL6306 with the ISL66xx
family of Intersil MOSFET drivers, which require 12V
bias.
3. The voltage on EN_VTT must be higher than 0.875V to
enable the controller. This pin is typically connected to the
output of VTT VR.
When all conditions above are satisfied, ISL6306 begins the
soft-start and ramps the output voltage to 1.1V first. After
ISL6306 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
remaining at 1.1V for some time, ISL6306 reads the VID
code at VID input pins. If the VID code is valid, ISL6306 will
V CC
+ 12 V
regulate the output to the final VID setting. If the VID code is
OFF code, ISL6306 will shut down, and cycling VCC,
POR
CIRCUIT
ENABLE
COMPARATOR
+
-
0.875V
10k Ω
EN_PWR
91 0Ω
EN_PWR or EN_VTT is needed to restart.
Soft-Start
ISL6306 based VR has 4 periods during soft-start as shown
in Figure 11. After VCC, EN_VTT and EN_PWR reach their
POR/enable thresholds, The controller will have fixed delay
period TD1. After this delay period, the VR will begin first
soft-start ramp until the output voltage reaches 1.1V V BOOT
voltage. Then, the controller will regulate the VR voltage at
+
-
EN_VTT
1.1V for another fixed period TD3. At the end of TD3 period,
ISL6306 reads the VID signals. If the VID code is valid,
ISL6306 will initiate the second soft-start ramp until the
voltage reaches the VID voltage minus offset voltage.
0.875V
The soft-start time is the sum of the 4 periods as shown in
SOFT-START
AND
Equation 14.
FAULT LOGIC
T SS = TD1 + TD2 + TD3 + TD4
(EQ. 14)
FIGURE 10. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (EN) FUNCTION
22
TD1 is a fixed delay with the typical value as 1.36ms. TD3 is
determined by the fixed 85μs plus the time to obtain valid
VID voltage. If the VID is valid before the output reaches the
1.1V, the minimum time to validate the VID input is 500ns.
Therefore the minimum TD3 is about 86μs.
FN9226.1
May 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6726AAZ-T | IC REG CTRLR ISO PWM CM 20-QSOP |
| ISL6565BCBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| ISL6565ACBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| AEB475M2WL32T-F | CAP ALUM 4.7UF 450V 20% SMD |
| AEB336M2CL32T-F | CAP ALUM 33UF 160V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6307ACRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307BCRZ | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR COM RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。