- 您现在的位置：买卖IC网 > PDF目录15170 > ISL6306IRZ-T (Intersil)IC REG CTRLR BUCK PWM VM 40-QFN PDF资料下载
参数资料
| 型号： | ISL6306IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 24/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 4,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 275kHz |
| 占空比： | 66.7% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
ISL6306
Overcurrent Protection
ISL6306 has two levels of overcurrent protection. Each
phase is protected from a sustained overcurrent condition on
a delayed basis, while the combined phase currents are
protected on an instantaneous basis.
In instantaneous protection mode, the ISL6306 utilizes the
sensed average current I AVG to detect an overcurrent
condition. See “Channel-Current Balance” on page 15 for
more detail on how the average current is measured. The
average current is continually compared with a constant
100 μ A reference current as shown in Figure 12. Once the
average current exceeds the reference current, a
comparator triggers the converter to shutdown.
In individual overcurrent protection mode, the ISL6306
continuously compares the current of each channel with the
same 100 μ A reference current. If any channel current
exceeds the reference current continuously for eight
consecutive cycles, the comparator triggers the converter to
shutdown.
Thermal Monitoring (VR_HOT/VR_FAN)
There are two thermal signals to indicate the temperature
status of the voltage regulator: VR_HOT and VR_FAN. Both
VR_FAN and VR_HOT are open-drain outputs, and external
pull-up resistors are required.
VR_FAN signal indicates that the temperature of the voltage
regulator is high and more cooling airflow is needed.
VR_HOT signal can be used to inform the system that the
temperature of the voltage regulator is too high and the CPU
should reduce its power consumption. VR_HOT signal may
be tied to the CPU’s PROC_HOT signal.
The diagram of thermal monitoring function block is shown in
Figure 14. One NTC resistor should be placed close to the
power stage of the voltage regulator to sense the operational
temperature, and one pull-up resistor is needed to form the
voltage divider for TM pin. As the temperature of the power
stage increases, the resistance of the NTC will reduce,
resulting in the reduced voltage at TM pin. Figure 15 shows
the TM voltage over the temperature for a typical design with
a recommended 6.8k Ω NTC (P/N: NTHS0805N02N6801
from Vishay) and 1k Ω resistor RTM1. We recommend using
those resistors for the accurate temperature compensation.
OUTPUT CURRENT
There are two comparators with hysteresis to compare the
TM pin voltage to the fixed thresholds for VR_FAN and
VR_HOT signals respectively. VR_FAN signal is set to high
0A
OUTPUT VOLTAGE
when TM voltage is lower than 33% of VCC voltage, and is
pulled to GND when TM voltage increases to above 39% of
VCC voltage. VR_FAN is set to high when TM voltage goes
below 28% of VCC voltage, and is pulled to GND when TM
voltage goes back to above 33% of VCC voltage. Figure 16
shows the operation of those signals.
0V
2ms/DIV
FIGURE 13. OVERCURRENT BEHAVIOR IN HICCUP MODE.
F SW = 500kHz
At the beginning of overcurrent shutdown, the controller
V CC
VR_FAN
places all PWM signals in a high-impedance state within
20ns commanding the Intersil MOSFET driver ICs to turn off
both upper and lower MOSFETs. The system remains in this
R
TM1
TM
0.33V CC
VR_HOT
state a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a soft-
o c
R
NTC
start. If the fault remains, the trip-retry cycles will continue
indefinitely (as shown in Figure 13) until either controller is
disabled or the fault is cleared. Note that the energy
delivered during trip-retry cycling is much less than during
full-load operation, so there is no thermal hazard during this
kind of operation.
24
0.28V CC
FIGURE 14. BLOCK DIAGRAM OF THERMAL MONITORING
FUNCTION
FN9226.1
May 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6726AAZ-T | IC REG CTRLR ISO PWM CM 20-QSOP |
| ISL6565BCBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| ISL6565ACBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| AEB475M2WL32T-F | CAP ALUM 4.7UF 450V 20% SMD |
| AEB336M2CL32T-F | CAP ALUM 33UF 160V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6307ACRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307BCRZ | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR COM RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。