- 您现在的位置：买卖IC网 > PDF目录15170 > ISL6306IRZ-T (Intersil)IC REG CTRLR BUCK PWM VM 40-QFN PDF资料下载
参数资料
| 型号： | ISL6306IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 26/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 4,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 275kHz |
| 占空比： | 66.7% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页
ISL6306
Depending on the location of the NTC and the airflow, the
NTC may be cooler or hotter than the current sense
component. TCOMP pin voltage can be utilized to correct
the temperature difference between NTC and the current
sense component. When a different NTC type or different
voltage divider is used for the TM function, TCOMP voltage
can also be used to compensate for the difference between
the recommended TM voltage curve in Figure 16 and that of
the actual design. According to the VCC voltage, ISL6306
converts the TCOMP pin voltage to a 4-bit TCOMP digital
signal as TCOMP factor N.
TCOMP factor N is an integer between 0 and 15. The
integrated temperature compensation function is disabled for
N = 0. For N = 4, the NTC temperature is equal to the
temperature of the current sense component. For N < 4, the
NTC is hotter than the current sense component. The NTC is
cooler than the current sense component for N > 4. When
N > 4, the larger TCOMP factor N, the larger the difference
between the NTC temperature and the temperature of the
current sense component.
ISL6306 multiplexes the TCOMP factor N with the TM digital
signal to obtain the adjustment gain to compensate the
temperature impact on the sensed channel current. The
compensated channel current signal is used for droop and
overcurrent protection functions.
Design Procedure
1. Properly choose the voltage divider for TM pin to match
the TM voltage V S temperature curve with the
recommended curve in Figure 15.
2. Run the actual board under the full load and the desired
cooling condition.
3. After the board reaches the thermal steady state, record
the temperature (T CSC ) of the current sense component
(inductor or MOSFET) and the voltage at TM and VCC
pins.
4. Use Equation 20 to calculate the resistance of the TM
NTC, and find out the corresponding NTC temperature
9. Run the actual board under full load again with the proper
resistors connected to the TCOMP pin.
10. Record the output voltage as V1 immediately after the
output voltage is stable with the full load. Record the
output voltage as V2 after the VR reaches the thermal
steady state.
11. If the output voltage increases over 2mV as the
temperature increases, i.e. V2 - V1 > 2mV, reduce N and
redesign R TC2 ; if the output voltage decreases over 2mV
as the temperature increases, i.e. V1 - V2 > 2mV,
increase N and redesign R TC2 .
The design spreadsheet is available for those calculations.
External Temperature Compensation
By setting the voltage of TCOMP pin to 0, the integrated
temperature compensation function is disabled. And one
external temperature compensation network, shown in
Figure 18, can be used to cancel the temperature impact on
the droop (i.e. load line).
COMP
FB
IDROOP
o c
VDIFF
FIGURE 18. VOLTAGE AT IDROOP PIN WITH A RESISTOR
PLACED FROM IDROOP PIN TO GND WHEN
LOAD CURRENT CHANGES
The sensed current will flow out of IDROOP pin and develop
the droop voltage across the resistor equivalent (R FB )
between FB and VDIFF pins. If R FB resistance reduces as
R NTC ( T ) = --------------------------------
V CC – V
TM
T NTC from the NTC datasheet.
V TM xR TM1
NTC
(EQ. 20)
the temperature increases, the temperature impact on the
droop can be compensated. An NTC resistor can be placed
close to the power stage and used to form R FB . Due to the
non-linear temperature characteristics of the NTC, a resistor
5. Use Equation 21 to calculate the TCOMP factor N:
network is needed to make the equivalent resistance
209x ( T CSC – T
N = -------------------------------------------------------- + 4
NTC
3xT NTC + 400
)
(EQ. 21)
between FB and VDIFF pin is reverse proportional to the
temperature.
6. Choose an integral number close to the above result for
the TCOMP factor. If this factor is higher than 15, use
N = 15. If it is less than 1, use N = 1.
7. Choose the pull-up resistor R TC1 (typical 10k Ω ).
8. If N = 15, do not need the pull-down resistor R TC2 ,
The external temperature compensation network can only
compensate the temperature impact on the droop, while it
has no impact to the sensed current inside ISL6306.
Therefore this network cannot compensate for the
temperature impact on the overcurrent protection function.
R TC2 = -----------------------
otherwise obtain R TC2 by Equation 22:
NxR TC1
15 – N
26
(EQ. 22)
Current Sense Output
The current from IDROOP pin is the sensed average current
inside ISL6306. In typical application, IDROOP pin is
connected to FB pin for the application where load line is
FN9226.1
May 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6726AAZ-T | IC REG CTRLR ISO PWM CM 20-QSOP |
| ISL6565BCBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| ISL6565ACBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| AEB475M2WL32T-F | CAP ALUM 4.7UF 450V 20% SMD |
| AEB336M2CL32T-F | CAP ALUM 33UF 160V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6307ACRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307BCRZ | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR COM RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。