- 您现在的位置：买卖IC网 > PDF目录15170 > ISL6306IRZ-T (Intersil)IC REG CTRLR BUCK PWM VM 40-QFN PDF资料下载
参数资料
| 型号： | ISL6306IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 31/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 4,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 275kHz |
| 占空比： | 66.7% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页
ISL6306
.
0.3
0.2
For a two phase design, use Figure 21 to determine the
input-capacitor RMS current requirement given the duty
cycle, maximum sustained output current (I O ), and the ratio
of the per-phase peak-to-peak inductor current (I L,P-P ) to I O .
Select a bulk capacitor with a ripple current rating which will
minimize the total number of input capacitors required to
support the RMS current calculated. The voltage rating of
the capacitors should also be at least 1.25 times greater
than the maximum input voltage.
0.1
I L,P-P = 0
I L,P-P = 0.5 I O
I L,P-P = 0.75 I O
Figures 22 and 23 provide the same input RMS current
information for three and four phase designs respectively.
Use the same approach to selecting the bulk capacitor type
and number as described above.
0
0
0.2
0.4
0.6
0.8
1.0
Low capacitance, high-frequency ceramic capacitors are
DUTY CYCLE (V O /V IN )
FIGURE 21. NORMALIZED INPUT-CAPACITOR RMS CURRENT
vs DUTY CYCLE FOR 2-PHASE CONVERTER
needed in addition to the bulk capacitors to suppress leading
and falling edge voltage spikes. The result from the high
current slew rates produced by the upper MOSFETs turn on
and off. Select low ESL ceramic capacitors and place one as
0.3
I L,P-P = 0
I L,P-P = 0.25 I O
I L,P-P = 0.5 I O
I L,P-P = 0.75 I O
close as possible to each upper MOSFET drain to minimize
board parasitic impedances and maximize suppression.
MULTIPHASE RMS IMPROVEMENT
Figure 23 is provided as a reference to demonstrate the
0.2
0.1
dramatic reductions in input-capacitor RMS current upon the
implementation of the multiphase topology. For example,
compare the input RMS current requirements of a two-phase
converter versus that of a single phase. Assume both
converters have a duty cycle of 0.25, maximum sustained
output current of 40A, and a ratio of I L,P-P to I O of 0.5. The
single phase converter would require 17.3A RMS current
capacity while the two-phase converter would only require
0
0
0.2
0.4
0.6
0.8
1.0
10.9A RMS . The advantages become even more pronounced
when output current is increased and additional phases are
DUTY CYCLE (V O/ V IN )
FIGURE 22. NORMALIZED INPUT-CAPACITOR RMS CURRENT
vs DUTY CYCLE FOR 3-PHASE CONVERTER
0.6
0.4
0.2
I L,P-P = 0
I L,P-P = 0.5 I O
I L,P-P = 0.75 I O
added to keep the component cost down relative to the
single phase approach.
Layout Considerations
The following layout strategies are intended to minimize the
impact of board parasitic impedances on converter
performance and to optimize the heat-dissipating capabilities
of the printed-circuit board. These sections highlight some
important practices which should not be overlooked during the
layout process.
Component Placement
Within the allotted implementation area, orient the switching
components first. The switching components are the most
critical because they carry large amounts of energy and tend
to generate high levels of noise. Switching component
placement should take into account power dissipation. Align
0
0
0.2
0.4
0.6
0.8
1.0
the output inductors and MOSFETs such that space between
the components is minimized while creating the PHASE
DUTY CYCLE (V O/ V IN )
FIGURE 23. NORMALIZED INPUT-CAPACITOR RMS
CURRENT vs DUTY CYCLE FOR SINGLE-PHASE
CONVERTER
31
plane. Place the Intersil MOSFET driver IC as close as
possible to the MOSFETs they control to reduce the parasitic
impedances due to trace length between critical driver input
FN9226.1
May 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6726AAZ-T | IC REG CTRLR ISO PWM CM 20-QSOP |
| ISL6565BCBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| ISL6565ACBZ | IC REG CTRLR BUCK PWM VM 28-SOIC |
| AEB475M2WL32T-F | CAP ALUM 4.7UF 450V 20% SMD |
| AEB336M2CL32T-F | CAP ALUM 33UF 160V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6307ACRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307AIRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6307BCRZ | 功能描述:软开关 PWM 控制器 W/ANNEAL 6-PHS VR11 CNTRLR COM RoHS:否 制造商:Fairchild Semiconductor 输出端数量: 输出电流: 开关频率: 工作电源电压:30 V 电源电流: 最大工作温度:+ 105 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。