参数资料
| 型号： | ISL6323CRZ |
| 厂商： | Intersil |
| 文件页数： | 21/36页 |
| 文件大小： | 0K |
| 描述： | IC HYBRID CTRLR PWM MONO 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 2 |
| 输出电压： | 最高 2V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ISL6323
During turn-off of the lower MOSFET, the PHASE voltage is
monitored until it reaches a -0.3V/+0.8V (forward/reverse
inductor current). At this time the UGATE is released to rise. An
auto-zero comparator is used to correct the r DS(ON) drop in the
phase voltage preventing false detection of the -0.3V phase
level during r DS(ON) conduction period. In the case of zero
current, the UGATE is released after 35ns delay of the LGATE
dropping below 0.5V. When LGATE first begins to transition
low, this quick transition can disturb the PHASE node and
cause a false trip, so there is 20ns of blanking time once
LGATE falls until PHASE is monitored.
Once the PHASE is high, the advanced adaptive
shoot-through circuitry monitors the PHASE and UGATE
voltages during a PWM falling edge and the subsequent
UGATE turn-off. If either the UGATE falls to less than 1.75V
above the PHASE or the PHASE falls to less than +0.8V, the
LGATE is released to turn-on.
Initialization
Prior to initialization, proper conditions must exist on the EN,
VCC, PVCC1_2, PVCC_NB, ISEN3-, and ISEN4- pins. When
the conditions are met, the controller begins soft-start. Once
the output voltage is within the proper window of operation,
the controller asserts VDDPWRGD.
The bias voltage applied to VCC must reach the internal
power-on reset (POR) rising threshold. Once this threshold
is reached, the ISL6323 has enough bias to begin checking
the driver POR inputs, EN, and channel detect portions of
the initialization cycle. Hysteresis between the rising and
falling thresholds assure the ISL6323 will not advertently
turn off unless the bias voltage drops substantially (see
“Electrical Specifications” on page 9).
The bias voltage applied to the PVCC1_2 and PVCC_NB
pins power the internal MOSFET drivers of each output
channel. In order for the ISL6323 to begin operation, both
PVCC inputs must exceed their POR rising threshold to
guarantee proper operation of the internal drivers.
Hysteresis between the rising and falling thresholds assure
that once enabled, the ISL6323 will not inadvertently turn off
unless the PVCC bias voltage drops substantially (see
“Electrical Specifications” on page 9). Depending on the
number of active CORE channels determined by the Phase
Detect block, the external driver POR checking is supported
by the Enable Comparator.
Enable Comparator
The ISL6323 features a dual function enable input (EN) for
enabling the controller and power sequencing between the
controller and external drivers or another voltage rail. The
ISL6323 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
VCC
PVCC1_2
enable comparator holds the ISL6323 in shutdown until the
voltage at EN rises above 0.86V. The enable comparator has
about 110mV of hysteresis to prevent bounce. It is important
that the driver ICs reach their rising POR level before the
ISL6323 becomes enabled. The schematic in Figure 12
PVCC_NB
+ 12 V
demonstrates sequencing the ISL6323 with the ISL66xx
family of Intersil MOSFET drivers, which require 12V bias.
POR
CIRCUIT
ENABLE
COMPARATOR
10.7k Ω
When selecting the value of the resistor divider the driver
maximum rising POR threshold should be used for
calculating the proper resistor values. This will prevent
+
-
V EN_THR
EN
1.00k Ω
improper sequencing events from creating false trips during
soft-start.
If the controller is configured for 2-phase CORE operation,
then the resistor divider can be used for sequencing the
controller with another voltage rail. The resistor divider to EN
SOFT-START
AND
FAULT LOGIC
CHANNEL
DETECT
ISEN3-
ISEN4-
should be selected using a similar approach as the previous
driver discussion.
The EN pin is also used to force the ISL6323 into either PVI
or SVI mode. The mode is set upon the rising edge of the EN
signal. When the voltage on the EN pin rises above 0.86V,
FIGURE 12. POWER SEQUENCING USING THRESHOLD-
SENSITIVE ENABLE (EN) FUNCTION
Power-On Reset
The ISL6323 requires VCC, PVCC1_2, and PVCC_NB
inputs to exceed their rising POR thresholds before the
ISL6323 has sufficient bias to guarantee proper operation.
21
the mode will be set depending upon the status of the
VID1/SEL pin.
Phase Detection
The ISEN3- and ISEN4- pins are monitored prior to soft-start
to determine the number of active CORE channel phases.
If ISEN4- is tied to VCC, the controller will configure the
channel firing order and timing for 3-phase operation. If
ISEN3- and ISEN4- are tied to VCC, the controller will set
FN9278.5
May 17, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| LD6806CX4/22H,315 | IC REG LDO 2.2V .2A 4WLCSP |
| 2256-18L | POWER CHOKE 27UH MOLDED AXIAL |
| 160MXC2200MEFCSN35X45 | CAP ALUM 2200UF 160V 20% SNAP-IN |
| 420MXG330MEFCSN30X35 | CAP ALUM 330UF 420V 20% SNAP-IN |
| 35MXC22000MEFCSN30X50 | CAP ALUM 22000UF 35V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6323CRZR5285 | 制造商:Intersil Corporation 功能描述: |
| ISL6323CRZ-T | 功能描述:IC HYBRID CTRLR PWM MONO 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL6323 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6323IRZ | 功能描述:IC HYBRID CTRLR PWM MONO 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323IRZ-T | 功能描述:IC HYBRID CTRLR PWM MONO 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。