参数资料
| 型号： | ISL6323CRZ |
| 厂商： | Intersil |
| 文件页数： | 24/36页 |
| 文件大小： | 0K |
| 描述： | IC HYBRID CTRLR PWM MONO 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 2 |
| 输出电压： | 最高 2V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ISL6323
I OCP = 100 μ A ? ------------- ? ---- ? ? ---------- ? R SET ? – ---------------------------------------- ? ----------------
2 ? L ? f S
V IN
more detail on how the average current is measured. Once
the average current exceeds 100μA, a comparator triggers
the converter to begin overcurrent protection procedures.
The Core regulator and the North Bridge regulator have the
same type of overcurrent protection.
The overcurrent trip threshold is dictated by the DCR of the
inductors, the number of active channels, the DC gain of the
inductor RC filter and the R SET resistor. The overcurrent trip
threshold is shown in Equation 20.
N 1 3 V IN – N ? V OUT V OUT
DCR K ? 400 ?
(EQ. 20)
Where:
overcurrent shutdown will be initiated. This will result in a
continuous hiccup mode.
Note that the energy delivered during trip-retry cycling is
much less than during full-load operation, so there is no
thermal hazard.
OUTPUT CURRENT, 50A/DIV
0A
OUTPUT VOLTAGE,
R 2
K = ---------------------
R 1 + R 2
500mV/DIV
f S = Switching Frequency
Equation 20 is valid for both the Core regulator and the
North Bridge regulator. This equation includes the DC load
current as well as the total ripple current contributed by all
the phases. For the North Bridge regulator, N is 1.
During soft-start, the overcurrent trip point is boosted by a
factor of 1.4. Instead of comparing the average measured
current to 100μA, the average current is compared to 140μA.
Immediately after soft-start is over, the comparison level
changes to 100μA. This is done to allow for start-up into an
active load while still supplying output capacitor in-rush
current.
CORE REGULATOR OVERCURRENT
At the beginning of overcurrent shutdown, the controller sets
all of the UGATE and LGATE signals low, puts PWM3 and
PWM4 (if active) in a high-impedance state, and forces
VDDPWRGD low. This turns off all of the upper and lower
MOSFETs. The system remains in this state for fixed period of
12ms. If the controller is still enabled at the end of this wait
period, it will attempt a soft-start, as shown in Figure 16. If the
fault remains, the trip-retry cycles will continue until either the
fault is cleared or for a total of seven attempts. If the fault is
not cleared on the final attempt, the controller disables
UGATE and LGATE signals for both Core and North Bridge
and latches off requiring a POR of VCC to reset the ISL6323.
It is important to note that during soft start, the overcurrent
trip point is increased by a factor of 1.4. If the fault draws
enough current to trip overcurrent during normal run mode, it
may not draw enough current during the soft-start ramp
period to trip overcurrent while the output is ramping up. If a
fault of this type is affecting the output, then the regulator will
complete soft-start and the trip-retry counter will be reset to
zero. Once the regulator has completed soft-start, the
overcurrent trip point will return to it’s nominal setting and an
24
0V
3ms/DIV
FIGURE 16. OVERCURRENT BEHAVIOR IN HICCUP MODE
NORTH BRIDGE REGULATOR OVERCURRENT
The overcurrent shutdown sequence for the North Bridge
regulator is identical to the Core regulator with the exception
that it is a single phase regulator and will only disable the
MOSFET drivers for the North Bridge. Once 7 retry attempts
have been executed unsuccessfully, the controller will disable
UGATE and LGATE signals for both Core and North Bridge
and will latch off requiring a POR of VCC to reset the ISL6323.
Note that the energy delivered during trip-retry cycling is
much less than during full-load operation, so there is no
thermal hazard.
Individual Channel Overcurrent Limiting
The ISL6323 has the ability to limit the current in each
individual channel of the Core regulator without shutting
down the entire regulator. This is accomplished by
continuously comparing the sensed currents of each channel
with a constant 140μA OCL reference current. If a channel’s
individual sensed current exceeds this OCL limit, the UGATE
signal of that channel is immediately forced low, and the
LGATE signal is forced high. This turns off the upper
MOSFET(s), turns on the lower MOSFET(s), and stops the
rise of current in that channel, forcing the current in the
channel to decrease. That channel’s UGATE signal will not
be able to return high until the sensed channel current falls
back below the 140μA reference.
Exclusive Operation in Parallel Mode
The ISL6323 was designed such that the processor would
be the determining factor of whether the ISL6323 operated
in PVI mode or in SVI mode. If, however, the ISL6323 is to
be used in a system that will be used exclusively in parallel
mode and the North Bridge regulator will not be populated at
FN9278.5
May 17, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| LD6806CX4/22H,315 | IC REG LDO 2.2V .2A 4WLCSP |
| 2256-18L | POWER CHOKE 27UH MOLDED AXIAL |
| 160MXC2200MEFCSN35X45 | CAP ALUM 2200UF 160V 20% SNAP-IN |
| 420MXG330MEFCSN30X35 | CAP ALUM 330UF 420V 20% SNAP-IN |
| 35MXC22000MEFCSN30X50 | CAP ALUM 22000UF 35V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6323CRZR5285 | 制造商:Intersil Corporation 功能描述: |
| ISL6323CRZ-T | 功能描述:IC HYBRID CTRLR PWM MONO 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL6323 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6323IRZ | 功能描述:IC HYBRID CTRLR PWM MONO 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323IRZ-T | 功能描述:IC HYBRID CTRLR PWM MONO 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。