参数资料
| 型号： | ISL6324ACRZ |
| 厂商： | Intersil |
| 文件页数： | 37/40页 |
| 文件大小： | 0K |
| 描述： | IC HYBRID CTRLR PWM DUAL 48QFN |
| 标准包装： | 43 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 2 |
| 输出电压： | 最高 2V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页
ISL6324A
3-phase and two-phase designs respectively. Use the same
approach for selecting the bulk capacitor type and number.
Low capacitance, high-frequency ceramic capacitors are
needed in addition to the input bulk capacitors to suppress
leading and falling edge voltage spikes. The spikes result from
the high current slew rate produced by the upper MOSFET
0.3
0.2
turn on and off. Select low ESL ceramic capacitors and place
one as close as possible to each upper MOSFET drain to
minimize board parasitics and maximize suppression.
0.1
Layout Considerations
MOSFETs switch very fast and efficiently. The speed with which
the current transitions from one device to another causes
voltage spikes across the interconnecting impedances and
parasitic circuit elements. These voltage spikes can degrade
efficiency, radiate noise into the circuit and lead to device
overvoltage stress. Careful component selection, layout, and
placement minimizes these voltage spikes. Consider, as an
example, the turnoff transition of the upper PWM MOSFET.
Prior to turnoff, the upper MOSFET was carrying channel
current. During the turn-off, current stops flowing in the upper
MOSFET and is picked up by the lower MOSFET. Any
inductance in the switched current path generates a large
voltage spike during the switching interval. Careful component
selection, tight layout of the critical components, and short, wide
circuit traces minimize the magnitude of voltage spikes.
I L(P-P) = 0
I L(P-P) = 0.5 I O
I L(P-P) = 0.75 I O
0
0 0.2 0.4 0.6 0.8 1.0
DUTY CYCLE (V IN/ V O )
FIGURE 28. NORMALIZED INPUT-CAPACITOR RMS
CURRENT FOR 2-PHASE CONVERTER
There are two sets of critical components in a DC/DC converter
using a ISL6324A controller. The power components are the
most critical because they switch large amounts of energy. Next
are small signal components that connect to sensitive nodes or
supply critical bypassing current and signal coupling.
The power components should be placed first, which include
the MOSFETs, input and output capacitors, and the inductors. It
is important to have a symmetrical layout for each power train,
0.3
I L(P-P) = 0
I L(P-P) = 0.25 I O
I L(P-P) = 0.5 I O
I L(P-P) = 0.75 I O
preferably with the controller located equidistant from each.
Symmetrical layout allows heat to be dissipated equally
across all power trains. Equidistant placement of the controller
to the CORE and NB power trains it controls through the
integrated drivers helps keep the gate drive traces equally
0.2
0.1
short, resulting in equal trace impedances and similar drive
capability of all sets of MOSFETs.
When placing the MOSFETs try to keep the source of the upper
FETs and the drain of the lower FETs as close as thermally
possible. Input high-frequency capacitors, C HF , should be
placed close to the drain of the upper FETs and the source of
the lower FETs. Input bulk capacitors, CBULK, case size
typically limits following the same rule as the high-frequency
0
0 0.2 0.4 0.6 0.8
DUTY CYCLE (V IN/ V O )
FIGURE 27. NORMALIZED INPUT-CAPACITOR RMS
CURRENT FOR 3-PHASE CONVERTER
37
1.0
input capacitors. Place the input bulk capacitors as close to the
drain of the upper FETs as possible and minimize the distance
to the source of the lower FETs.
Locate the output inductors and output capacitors between the
MOSFETs and the load. The high-frequency output decoupling
capacitors (ceramic) should be placed as close as practicable
to the decoupling target, making use of the shortest connection
paths to any internal planes, such as vias to GND next or on the
capacitor solder pad.
FN6880.2
May 14, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| 1782-83J | COIL RF 430UH MOLDED UNSHIELDED |
| LT1529CT-5#PBF | IC REG LDO 5V 3A TO220 |
| 2150-20K | COIL RF 6.8UH MOLDED UNSHIELDED |
| 2150-18K | COIL RF 5.6UH MOLDED UNSHIELDED |
| LT1529CT#PBF | IC REG LDO ADJ 3A TO220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6324ACRZR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONTROLLER, CORE+NORTHBRIDGE, PROG PSI, 3.4MHZ SVI - Rail/Tube 制造商:Intersil Corporation 功能描述:IC HYBRID CTRLR PWM DUAL 48QFN |
| ISL6324ACRZ-T | 功能描述:IC HYBRID CTRLR PWM DUAL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6324ACRZ-TR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONT., CORE + NORTHBRIDGE, PROG PSI, 3.4MHZ SVI, 5 - Tape and Reel 制造商:Intersil Corporation 功能描述:IC HYBRID CTRLR PWM DUAL 48QFN |
| ISL6324AIRZ | 功能描述:IC HYBRID CTRLR PWM DUAL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6324AIRZR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONTROLLER, CORE + NORTHBRIDGE, PROG PSI, 3.4MHZ S - Rail/Tube 制造商:Intersil Corporation 功能描述:IC HYBRID CTRLR PWM DUAL 48QFN |
发布紧急采购，3分钟左右您将得到回复。