- 您现在的位置：买卖IC网 > PDF目录17320 > ISL8120EVAL3Z (Intersil)EVALUATION BOARD FOR ISL8120 PDF资料下载
参数资料
| 型号： | ISL8120EVAL3Z |
| 厂商： | Intersil |
| 文件页数： | 20/35页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR ISL8120 |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.2V，1.2V |
| 电流 - 输出： | 2 x 25A 或 1 x 50A |
| 输入电压： | 3 ~ 22 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 150kHz ~ 1.5MHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL8120 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
ISL8120
VSEN1- resistor is 100 Ω and it should not be large in order
to keep the unit gain amplifier input impedance compatibility.
VMON1, VMON2 (Pins 31, 11)
These pins are outputs of the unity gain amplifiers. They are
connected internally to the OV/UV/PGOOD comparators.
These pins should be connected to the FB1, FB2 pins by a
standard feedback network when both channels are operating
independently. When VSEN1-, VSEN2- are pulled within
700mV of VCC, the corresponding differential amplifier is
disabled and its output (VMON pin) is high impedance. In
such an event, the VMON pin can be used as an additional
monitor of the output voltage with a resistor divider to protect
the system against single point of failure, which occurs in the
system using the same resistor divider for both of the UV/OV
comparator and output voltage feedback.
Modes of Operation
There are 9 typical operation modes depending upon the
signal levels on EN1/FF1, EN2/FF2, VSEN2+, VSEN2-,
FB2, and CLKOUT/REFIN.
MODE 1: The IC is completely disabled when EN1/FF1 and
EN2/FF2 are pulled below 0.8V.
MODE 2: With EN1/FF1 pulled low and EN2/FF2 pulled high
(Mode 2A), or EN1/FF1 pulled high and EN2/FF2 pulled low
(Mode 2B), the ISL8120 operates as a single phase
regulator. The current sourcing out from the ISHARE pin
represents the first channel current plus 15μA offset current.
MODE 3: When VSEN2- is used as a negative sense line,
both channels’ phase shift depends upon the voltage level of
CLKOUT/REFIN. When the CLKOUT/REFIN pin is within
29% to 45% of VCC, Channel 2 delays 0° over Channel 1
(Mode 3A); when within 45% to 62% of VCC, 90°delay
(Mode 3B); when greater than 62% to VCC, 180° delay
MODE 4: When VSEN2- is used as a negative remote sense
line, and CLKOUT/REFIN is connected to an external
voltage ramp lower than the internal soft-start ramp and
lower than 0.6V, the external ramp signal will replace
Channel 2’s internal soft-start ramp to be tracked at start-up,
controller operating in DDR mode. The controller will use the
lowest voltage among the internal 0.6V reference, the
external voltage in CLKOUT/REFIN pin and the soft-start
ramp signal. Channel 1 is delayed 60° behind Channel 2.
20
MODE 5: With VSEN2- pulled within 700mV of VCC and
FB2 pulled to ground, the internal channels are 180°
out-of-phase and operate in 2-phase single output mode
(5A). The CLKOUT/REFIN pin (rising edge) also signals out
clock with 60° phase shift relative to the Channel 1’s clock
signal (falling edge of PWM) for 6-phase operation with two
other ISL8120s (5B). When the share pins are not
connected to each other for the three ICs in sync, two of
which can operate in Mode 5A (3 independent outputs can
be generated (Mode 5D)) and Modes 3 and 4 (to generate 4
independent outputs (Mode 5C)) respectively.
MODE 6: With VSEN2- pulled within 700mV of VCC, FB2
pulled high and VSEN2+ pulled low, the internal channels
(as 1st and 3rd Phase, respectively) are 240° out-of-phase
and operate in 3-phase single output mode, combined with
another ISL8120 at MODE 2B. The CLKOUT/REFIN pin
signals out 120° relative phases to the falling edge of
Channel 1’s clock signal to synchronize with the second
ISL8120’s Channel 1 (as 2nd Phase).
MODE 7: With VSEN2- pulled within 700mV of VCC and
FB2 and VSEN2+ pulled high, the internal channel is 180°
out-of-phase. The CLKOUT/REFIN pin (rising edge) signals
out 90° relative phase to the Channel 1’s clock signal (falling
edge of PWM) to synchronize with another ISL8120, which
can operate at Mode 3, 4, 5A, or 7A. A 4-phase single output
converter can be constructed with two ISL8120s operating in
Mode 5A or 7A (Mode 7A). If the share bus is not connected
between ICs, each IC could generate an independent output
(Mode 7B). When the second ISL8120 operates as two
independent regulators (Mode 3) or in DDR mode (Mode 4),
then a three independent output system is generated (Mode
7C). Both ICs can also be constructed as a 3-phase
converter (0°, 90°, and 180°, not a equal phase shift for
3-phase) with a single phase regulator (270°).
MODE 8 : The output CLKOUT signal allows expansion for
12-phase operation with the cascaded sequencing, as
shown in Table 1. No external clock is required in this mode
for the desired phase shift.
MODE 9: With an external clock, the part can be expanded
for 5, 7, 8, 9 10 and 11 phase single output operation with
the desired phase shift.
March 20, 2009
FN6641.0
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6455AEVAL1Z | EVALUATION BOARD FOR ISL6455A |
| ISL6455EVAL1Z | EVALUATION BOARD FOR ISL6455 |
| GBC13DCAH | CONN EDGECARD 26POS R/A .100 SLD |
| GBC13DCAD | CONN EDGECARD 26POS R/A .100 SLD |
| EEC20DRYS | CONN EDGECARD 40POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8120EVAL4Z | 功能描述:BOARD EVALUATION FOR ISL8120 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8120IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8120IRZEC | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8120IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8120IRZ-TEC | 功能描述:IC REG CTRLR BUCK PWM VM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。