- 您现在的位置：买卖IC网 > PDF目录13623 > ISL85402IRZ-TK (Intersil)IC REG BUCK BOOST SYNC ADJ 20QFN PDF资料下载
参数资料
| 型号： | ISL85402IRZ-TK |
| 厂商： | Intersil |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BOOST SYNC ADJ 20QFN |
| 标准包装： | 1,000 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 0.8V |
| 输入电压： | 3 V ~ 36 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 2.2MHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 两者兼有 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 20-QFN（4x4） |
ISL85402
reflect reality. As a result, the actual capacitance may be
considerably lower than the advertised value. Consult the
manufacturers data sheet to determine the actual in-application
capacitance. Most manufacturers publish capacitance vs DC bias
so that this effect can be easily accommodated. The effects of
AC voltage are not frequently published, but an assumption of
~20% further reduction will generally suffice. The result of these
considerations can easily result in an effective capacitance 50%
lower than the rated value. Nonetheless, they are a very good
choice in many applications due to their reliability and extremely
low ESR.
The following equations allow calculation of the required
capacitance to meet a desired ripple voltage level. Additional
capacitance may be used.
Increasing the value of inductance reduces the ripple current and
thus ripple voltage. However, the larger inductance value may
reduce the converter’s response time to a load transient. The
inductor current rating should be such that it will not saturate in
overcurrent conditions.
Low-Side Power MOSFET
In synchronous buck application, a power N MOSFET is needed
as the synchronous low side MOSFET and a good one should
have low Qgd, low r DS(ON) and small Rg (Rg_typ < 1.5 ?
recommended ) . Vgth_min is recommended to be higher than
1.2V. A good example is SQS462EN.
Output Voltage Feedback Resistor Divider
V OUTripple = -----------------------------------
V OUT = 0.8 ? ? 1 + --------------------- ?
? R UP ?
For the ceramic capacitors (low ESR):
Δ I
8 ? F SW ? C OUT
(EQ. 11)
The output voltage can be programmed down to 0.8V by a
resistor divider from V OUT to FB according to Equation 15.
(EQ. 15)
? R LOW ?
where Δ I is the inductor’s peak to peak ripple current, F SW is the
switching frequency and C OUT is the output capacitor.
If using electrolytic capacitors then:
In an application requiring least input quiescent current, large
resistors should be used for the divider. 232k is recommended
for the upper resistor.
V OUTripple = Δ I*ESR
(EQ. 12)
Loop Compensation Design
V OUT 2 * ( V OUTMAX ? V OUT ) 2 – 1 )
Regarding transient response needs, a good starting point is to
determine the allowable overshoot in V OUT if the load is suddenly
removed. In this case, energy stored in the inductor will be
transferred to C OUT causing its voltage to rise. After calculating
capacitance required for both ripple and transient needs, choose
the larger of the calculated values. The following equation
determines the required output capacitor value in order to
achieve a desired overshoot relative to the regulated voltage.
I OUT 2 * L
C OUT = ------------------------------------------------------------------------------------- (EQ. 13)
The ISL85402 uses constant frequency peak current mode
control architecture to achieve fast loop transient response. An
accurate current sensing pilot device in parallel with the upper
MOSFET is used for peak current control signal and overcurrent
protection. The inductor is not considered as a state variable
since its peak current is constant, and the system becomes
single order system. It is much easier to design the compensator
to stabilize the loop compared with voltage mode control. Peak
current mode control has inherent input voltage feed-forward
function to achieve good line regulation. Figure 29 shows the
small signal model of a buck regulator.
where V OUTMAX /V OUT is the relative maximum overshoot
allowed during the removal of the load.
Input Capacitors
Depending on the system input power rail conditions, the
aluminum electrolytic type capacitor is normally needed to
+
^
i in
^
V in
IL d ^
1:D
V in d ^
^
i L
L P
RT
R LP
Rc
^
v o
provide the stable input voltage. Thus, restrict the switching
frequency pulse current in a small area over the input traces for
better EMC performance. The input capacitor should be able to
Co
Ro
handle the RMS current from the switching power devices.
Ceramic capacitors must be used at VIN pin of the IC and
multiple capacitors including 1μF and 0.1μF are recommended.
Place these capacitors as closely as possible to the IC.
d ^
Fm
T i(S)
Buck Output Inductor
The inductor value determines the converter’s ripple current.
Choosing an inductor current requires a somewhat arbitrary
+
He(S)
v ^ comp
-Av(S)
Tv (S)
choice of ripple current, Δ I. A reasonable starting point is 30% to
40% of total load current. The inductor value can then be
calculated using Equation 14:
FIGURE 29. SMALL SIGNAL MODEL OF BUCK REGULATOR
V IN – V OUT V OUT
Fs × Δ I
L = ---------------------------- × -------------
V IN
17
(EQ. 14)
FN7640.1
April 25, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6733AUTYVD2+T | IC SUPERVISOR MPU W/WD SOT23-6 |
| 35ZLK330MT810X16 | CAP ALUM 330UF 35V 20% RADIAL |
| MAX6733AUTYDD1+T | IC SUPERVISOR MPU W/WD SOT23-6 |
| ISL85402IRZ-T | IC REG BUCK BOOST SYNC ADJ 20QFN |
| MAX6733AUTZID5+T | IC SUPERVISOR MPU W/WD SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8540EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL8540 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8540IVEZ | 功能描述:IC REG BUCK SYNC ADJ 2A 20HTSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:1 系列:EZBuck™ 类型:降压（降压） 输出类型:可调式 输出数:1 输出电压:0.8 V ~ 22.1 V 输入电压:3 V ~ 26 V PWM 型:电流模式 频率 - 开关:1.5MHz 电流 - 输出:1.8A 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 包装:剪切带 (CT) 供应商设备封装:8-DFN（2x2） 其它名称:785-1276-1 |
| ISL8540IVEZ-T | 功能描述:IC REG BUCK SYNC ADJ 2A 20HTSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
| ISL85410FRZ | 制造商:Intersil Corporation 功能描述:36VIN 1A SYNCHRONOUS SWITCHING REGULATOR- 4X3 12LD DFN PB-FR - Rail/Tube 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 1A 12DFN |
| ISL85410FRZ-T | 制造商:Intersil Corporation 功能描述:36VIN 1A SYNCHRONOUS SWITCHING REGULATOR 4X3 12LD DFN T&R - Tape and Reel 制造商:Intersil Corporation 功能描述:IC REG BUCK SYNC ADJ 1A 12DFN |
发布紧急采购，3分钟左右您将得到回复。