- 您现在的位置：买卖IC网 > PDF目录79959 > L6919ETR (STMICROELECTRONICS) SWITCHING CONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | L6919ETR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO28 |
| 封装： | SO-28 |
| 文件页数： | 31/33页 |
| 文件大小： | 644K |
| 代理商： | L6919ETR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页
Obsolete
Product(s)
- Obsolete
Product(s)
7/33
L6919E
17
OSC/INH
FAULT
Oscillator pin.
It allows programming the switching frequency of each channel: the equivalent switching
frequency at the load side results in being doubled.
Internally fixed at 1.24V, the frequency is varied proportionally to the current sunk (forced) from
(into) the pin with an internal gain of 6kHz/
A (See relevant section for details). If the pin is not
connected, the switching frequency is 150kHz for each channel (300kHz on the load).
The pin is forced high (5V Typ.) when an Over/Under Voltage is detected; to recover from this
condition, cycle VCC.
Forcing the pin to a voltage lower than 0.6V, the device stop operation and enter the inhibit
state.
18-22
VID4-0
Voltage IDentification pins.
Internally pulled-up, connect to GND to program a ‘0’ while leave floating to program a ‘1’.
They are used to program the output voltage as specified in Table 1 and to set the PGOOD,
OVP and UVP thresholds.
The device automatically regulates 25mV higher than the HAMMER DAC avoiding the use of
any external set-up resistor.
23
PGOOD
This pin is an open collector output and is pulled low if the output voltage is not within the above
specified thresholds and during soft start. It cannot be pulled-up above 5V.
If not used may be left floating.
24
BOOT2
Channel 2 HS driver supply. This pin supplies the relative high side driver.
Connect through a capacitor (100nF typ.) to the PHASE2 pin and through a diode to VCC
(cathode vs. boot).
25
UGATE2
Channel 2 HS driver output.
A little series resistor helps in reducing device-dissipated power.
26
PHASE2
Channel 2 HS driver return path. It must be connected to the HS2 mosfet source and provides
the return path for the HS driver of channel 2.
27
LGATE2
Channel 2 LS driver output.
A little series resistor helps in reducing device-dissipated power.
28
PGND
LS drivers return path.
This pin is common to both sections and it must be connected through the closest path to the
LS mosfets source pins in order to reduce the noise injection into the device.
PIN FUNCTION (continued)
N
Name
Description
相关PDF资料 |
PDF描述 |
|---|---|
| LUW025F8 | 1-OUTPUT 16.5 W DC-DC REG PWR SUPPLY MODULE |
| L5973ADTR | 2.3 A SWITCHING REGULATOR, PDSO8 |
| LSN-1.8/10-D12BH | DC-DC REG PWR SUPPLY MODULE |
| LM2575-33IN | 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP16 |
| LM2575IKTT | 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L-692 | 制造商:RHOMBUS-IND 制造商全称:Rhombus Industries Inc. 功能描述:Common Mode Inductor |
| L6920 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1V HIGH EFFICIENCY SYNCRONOUS STEP UP CONVERTER |
| L6920D | 功能描述:直流/直流开关转换器 0.6 to 5.5V Step-Up RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| L6920DB | 功能描述:直流/直流开关转换器 Synchronous Rectifer Step Up Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| L6920DBTR | 功能描述:直流/直流开关转换器 SYNCRONOUS RECT. STEP UP CONVERTER RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。