- 您现在的位置：买卖IC网 > PDF目录79959 > L6919ETR (STMICROELECTRONICS) SWITCHING CONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | L6919ETR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO28 |
| 封装： | SO-28 |
| 文件页数： | 9/33页 |
| 文件大小： | 644K |
| 代理商： | L6919ETR |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Obsolete
Product(s)
- Obsolete
Product(s)
17/33
L6919E
to reduce switching noise above all during load transient. Ceramic capacitor can also introduce benefits in high
frequency noise decoupling, noise generated by parasitic components along power path.
OUTPUT CAPACITOR
Since the microprocessors require a current variation beyond 50A doing load transients, with a slope in the
range of tenth A/
s, the output capacitor is a basic component for the fast response of the power supply.
Dual phase topology reduces the amount of output capacitance needed because of faster load transient response
(switching frequency is doubled at the load connections). Current ripple cancellation due to the 180° phase shift
between the two phases also reduces requirements on the output ESR to sustain a specified voltage ripple.
When a load transient is applied to the converter's output, for first few microseconds the current to the load is sup-
plied by the output capacitors. The controller recognizes immediately the load transient and increases the duty
cycle, but the current slope is limited by the inductor value.
The output voltage has a first drop due to the current variation inside the capacitor (neglecting the effect of the
ESL):
VOUT = IOUT ESR
A minimum capacitor value is required to sustain the current during the load transient without discharge it. The
voltage drop due to the output capacitor discharge is given by the following equation:
Where DMAX is the maximum duty cycle value. The lower is the ESR, the lower is the output drop during load
transient and the lower is the output voltage static ripple.
INDUCTOR DESIGN
The inductance value is defined by a compromise between the transient response time, the efficiency, the cost
and the size. The inductor has to be calculated to sustain the output and the input voltage variation to maintain
the ripple current
IL between 20% and 30% of the maximum output current. The inductance value can be cal-
culated with this relationship:
Where fSW is the switching frequency, VIN is the input voltage and VOUT is the output voltage.
Increasing the value of the inductance reduces the ripple current but, at the same time, reduces the converter
response time to a load transient. The response time is the time required by the inductor to change its current
from initial to final value. Since the inductor has not finished its charging time, the output current is supplied by
the output capacitors. Minimizing the response time can minimize the output capacitance required.
The response time to a load transient is different for the application or the removal of the load: if during the ap-
plication of the load the inductor is charged by a voltage equal to the difference between the input and the output
voltage, during the removal it is discharged only by the output voltage. The following expressions give approx-
imate response time for
I load transient in case of enough fast compensation network response:
The worst condition depends on the input voltage available and the output voltage selected. Anyway the worst
case is the response time after removal of the load with the minimum output voltage programmed and the max-
imum input voltage available.
V
OUT
I
OUT
2
L
4C
OUT
V
IN
D
MAX
V
OUT
–
()
-----------------------------------------------------------------------------------
=
L
V
IN
V
OUT
–
f
SW
I
L
------------------------------
V
OU T
V
IN
---------------
=
t
a pplic atio n
LI
V
IN
V
OUT
–
------------------------------
=
t
removal
LI
V
OUT
---------------
=
相关PDF资料 |
PDF描述 |
|---|---|
| LUW025F8 | 1-OUTPUT 16.5 W DC-DC REG PWR SUPPLY MODULE |
| L5973ADTR | 2.3 A SWITCHING REGULATOR, PDSO8 |
| LSN-1.8/10-D12BH | DC-DC REG PWR SUPPLY MODULE |
| LM2575-33IN | 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP16 |
| LM2575IKTT | 4 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L-692 | 制造商:RHOMBUS-IND 制造商全称:Rhombus Industries Inc. 功能描述:Common Mode Inductor |
| L6920 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1V HIGH EFFICIENCY SYNCRONOUS STEP UP CONVERTER |
| L6920D | 功能描述:直流/直流开关转换器 0.6 to 5.5V Step-Up RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| L6920DB | 功能描述:直流/直流开关转换器 Synchronous Rectifer Step Up Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| L6920DBTR | 功能描述:直流/直流开关转换器 SYNCRONOUS RECT. STEP UP CONVERTER RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。