参数资料
| 型号： | LT1977IFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 16TSSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.2 V ~ 54 V |
| 输入电压： | 3.3 V ~ 60 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-TSSOP-EP |
LT1977
PI FU CTIO S
voltage on the PGFB pin drops below V PGFB , C CT will be
discharged rapidly to 0V and PG will be active low with a
200 μ A sink capability. If the C T pin is clamped (Power Good
condition) during normal operation and SHDN is taken low,
the C T pin will be discharged and a delay period will occur
when SHDN is returned high. See the Power Good section
in Applications Information for details.
GND (Pins 8, 17): The GND pin connection acts as the
reference for the regulated output, so load regulation will
suffer if the “ground” end of the load is not at the same
voltage as the GND pin of the IC. This condition will occur
when load current or other currents flow through metal
paths between the GND pin and the load ground. Keep the
path between the GND pin and the load ground short and
use a ground plane when possible. The GND pin also acts
as a heat sink and should be soldered (along with the
exposed leadframe) to the copper ground plane to reduce
thermal resistance (see Applications Information).
C SS (Pin 9): A capacitor from the C SS pin to the regulated
output voltage determines the output voltage ramp rate
during start-up. When the current through the C SS capaci-
tor exceeds the C SS threshold (I CSS ), the voltage ramp of
the output is limited. The C SS threshold is proportional to
the FB voltage (see Typical Performance Characteristics)
and is defeated for FB voltage greater than 0.9V (typical).
See Soft-Start section in Applications Information for
details.
BIAS (Pin 10): The BIAS pin is used to improve efficiency
when operating at higher input voltages and light load
current. Connecting this pin to the regulated output volt-
age forces most of the internal circuitry to draw its
operating current from the output voltage rather than the
input supply. This architecture increases efficiency espe-
cially when the input voltage is much higher than the
output. Minimum output voltage setting for this mode of
operation is 3V.
V C (Pin 11): The V C pin is the output of the error amplifier
and the input of the peak switch current comparator. It is
normally used for frequency compensation, but can also
serve as a current clamp or control loop override. V C sits
During the sleep portion of Burst Mode operation, the V C
pin is held at a voltage slightly below the burst threshold
for better transient response. Driving the V C pin to ground
will disable switching and place the IC into sleep mode.
FB (Pin 12): The feedback pin is used to determine the
output voltage using an external voltage divider from the
output that generates 1.25V at the FB pin . When the FB pin
drops below 0.9V, switching frequency is reduced, the
SYNC function is disabled and output ramp rate control is
enabled via the C SS pin. See the Feedback section in
Applications Information for details.
PGFB (PIN 13): The PGFB pin is the positive input to a
comparator whose negative input is set at V PGFB . When
PGFB is taken above V PGFB , current (I CSS ) is sourced into
the C T pin starting the PG delay period. When the voltage
on the PGFB pin drops below V PGFB , the C T pin is rapidly
discharged resetting the PG delay period. The PGFB volt-
age is typically generated by a resistive divider from the
regulated output or input supply. See Power Good section
in Applications Information for details.
SYNC (Pin 14): The SYNC pin is used to synchronize the
internal oscillator to an external signal. It is directly logic
compatible and can be driven with any signal between
30% and 70% duty cycle. The synchronizing range is
equal to maximum initial operating frequency up to 700kHz.
When the voltage on the FB pin is below 0.9V the SYNC
function is disabled. See the Synchronizing section in
Applications Information for details.
SHDN (Pin 15): The SHDN pin is used to turn off the
regulator and to reduce input current to less than 1 μ A. The
SHDN pin requires a voltage above 1.3V with a typical
source current of 5 μ A to take the IC out of the shutdown
state.
PG (Pin 16): The PG pin is functional only when the SHDN
pin is above its threshold, and is active low when the
internal clamp on the C T pin is below its clamp level and
high impedance when the clamp is active. The PG pin has
a typical sink capability of 200 μ A. See the Power Good
section in Applications Information for details.
at about 0.45V for light loads and 2.2V at maximum load.
1977fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| LT3008EDC-1.2#TRMPBF | IC REG LDO 1.2V 20MA 6-DFN |
| LT3009ESC8-1.5#TRMPBF | IC REG LDO 1.5V 20MA SC70-8 |
| LT3010MPMS8E-5#TRPBF | IC REG LDO 5V 50MA 8-MSOP |
| LT3011HMSE#TRPBF | IC REG LDO ADJ 50MA 12-MSOP |
| LT3012HFE#TRPBF | IC REG LDO ADJ .2A 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1990 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Precision, 100μA Gain Selectable Amplifier |
| LT1990ACS8 | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:2pA 电压 - 输入偏移:1000µV 电流 - 电源:85µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:剪切带 (CT) 产品目录页面:680 (CN2011-ZH PDF) 其它名称:MCP6L04T-E/SLCT |
| LT1990ACS8#PBF | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LT1990ACS8#TR | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:2pA 电压 - 输入偏移:1000µV 电流 - 电源:85µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:剪切带 (CT) 产品目录页面:680 (CN2011-ZH PDF) 其它名称:MCP6L04T-E/SLCT |
| LT1990ACS8#TRPBF | 功能描述:IC AMP DIFF +/-250V MCRPWR 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:2pA 电压 - 输入偏移:1000µV 电流 - 电源:85µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:剪切带 (CT) 产品目录页面:680 (CN2011-ZH PDF) 其它名称:MCP6L04T-E/SLCT |
发布紧急采购，3分钟左右您将得到回复。