- 您现在的位置：买卖IC网 > PDF目录10302 > LTC2412IGN#TR (Linear Technology)IC CONV A/D 24B 2CH DIFF 16-SSOP PDF资料下载
参数资料
| 型号： | LTC2412IGN#TR |
| 厂商： | Linear Technology |
| 文件页数： | 4/36页 |
| 文件大小： | 0K |
| 描述： | IC CONV A/D 24B 2CH DIFF 16-SSOP |
| 标准包装： | 2,500 |
| 位数： | 24 |
| 采样率（每秒）： | 7.5 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，双极 |
| 配用： | DC746A-ND - BOARD DELTA SIGMA ADC LTC2412 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC2412
12
2412f
CONVERTER OPERATION
Converter Operation Cycle
The LTC2412 is a low power,
Σ ADC with automatic
alternate channel selection between the two differential
channels and an easy-to-use 3-wire serial interface (see
Figure 1). Channel 0 is selected automatically at power up
and the two channels are selected alternately afterwards
(ping-pong). Its operation is made up of three states. The
converter operating cycle begins with the conversion,
followed by the low power sleep state and ends with the
data output (see Figure 2). The 3-wire interface consists
of serial data output (SDO), serial clock (SCK) and chip
select (CS).
Initially, the LTC2412 performs a conversion. Once the
conversion is complete, the device enters the sleep state.
The part remains in the sleep state as long as CS is HIGH.
While in this sleep state, power consumption is reduced by
nearly two orders of magnitude. The conversion result is
held indefinitely in a static shift register while the converter
is in the sleep state.
Once CS is pulled LOW, the device exits the low power
mode and enters the data output state. If CS is pulled HIGH
before the first rising edge of SCK, the device returns to the
low power sleep mode and the conversion result is still
held in the internal static shift register. If CS remains LOW
after the first rising edge of SCK, the device begins
outputting the conversion result. Taking CS high at this
point will terminate the data output state and start a new
conversion. There is no latency in the conversion result.
The data output corresponds to the conversion just per-
formed. This result is shifted out on the serial data out pin
(SDO) under the control of the serial clock (SCK). Data is
updated on the falling edge of SCK allowing the user to
reliably latch data on the rising edge of SCK (see Figure 3).
The data output state is concluded once 32 bits are read
out of the ADC or when CS is brought HIGH. The device
automatically initiates a new conversion and the cycle
repeats.
Through timing control of the CS and SCK pins, the
LTC2412 offers several flexible modes of operation
(internal or external SCK and free-running conversion
modes). These various modes do not require program-
ming configuration registers; moreover, they do not dis-
turb the cyclic operation described above. These modes of
operation are described in detail in the Serial Interface
Timing Modes section.
Conversion Clock
A major advantage the delta-sigma converter offers over
conventional type converters is an on-chip digital filter
(commonly implemented as a Sinc or Comb filter). For
high resolution, low frequency applications, this filter is
typically designed to reject line frequencies of 50Hz or
60Hz plus their harmonics. The filter rejection perfor-
mance is directly related to the accuracy of the converter
system clock. The LTC2412 incorporates a highly accu-
rate on-chip oscillator. This eliminates the need for exter-
nal frequency setting components such as crystals or
oscillators. Clocked by the on-chip oscillator, the LTC2412
achieves a minimum of 110dB rejection at the line fre-
quency (50Hz or 60Hz
±2%).
Ease of Use
The LTC2412 data output has no latency, filter settling
delay or redundant data associated with the conversion
cycle. There is a one-to-one correspondence between the
conversion and the output data. Therefore, multiplexing
multiple analog voltages is easy.
APPLICATIO S I FOR ATIO
WU
U
Figure 2. LTC2412 State Transition Diagram
CONVERT
POWER UP
IN+ = CH0+, IN– = CH0–
SLEEP
DATA OUTPUT
SWITCH CHANNEL
2412 F02
TRUE
FALSE
CS = LOW
AND
SCK
相关PDF资料 |
PDF描述 |
|---|---|
| AD7401YRWZ-REEL7 | IC MODULATOR SIGMA-DELTA 16SOIC |
| VE-BTZ-MV-S | CONVERTER MOD DC/DC 2V 60W |
| AD7924WYRUZ-REEL7 | IC ADC 12BIT 4CH W/SEQ 16TSSOP |
| VE-BTX-MW-S | CONVERTER MOD DC/DC 5.2V 100W |
| AD7705BRU-REEL | IC ADC 16BIT 2CH 16-TSSOP T/R |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC2413CGN | 功能描述:IC A/D CONV 24BIT MICRPWR 16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2413CGN#PBF | 功能描述:IC A/D CONV 24BIT MICRPWR 16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| LTC2413CGN#TR | 功能描述:IC ADC 24BIT 50/60HZ MPWR 16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2413CGN#TRPBF | 功能描述:IC A/D CONV 24BIT MICRPWR 16SSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| LTC2413IGN | 功能描述:IC A/D CONV 24BIT MICRPWR 16SSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。