- 您现在的位置：买卖IC网 > PDF目录1831 > LTC3703IGN#PBF (Linear Technology)IC REG CTRLR BST PWM VM 16-SSOP PDF资料下载
参数资料
| 型号： | LTC3703IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/34页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM VM 16-SSOP |
| 标准包装： | 100 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 96% |
| 电源电压： | 9.3 V ~ 15 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC3703
APPLICATIONS INFORMATION
V OUT
V IN
V IN – V OUT
V IN
( I MAX ) 2 (1 + δ )R DS(ON) +
P MAIN =
V
+ V
–
V IN2 MAX (R DR )(C MILLER ) ?
? ? V CC – V TH(IL)
V TH(IL) ? ?
(I MAX ) 2 (1 + δ )R DS(0N)
P SYNC = IN
breakdownspecification.SincemanyhighvoltageMOS-
FETs have higher threshold voltages (typically, V GS(MIN)
≥ 6V), the LTC3703 is designed to be used with a 9V to
15V gate drive supply (DRV CC pin).
For maximum efficiency, on-resistance R DS(ON) and input
capacitance should be minimized. Low R DS(ON) minimizes
conduction losses and low input capacitance minimizes
transition losses. MOSFET input capacitance is a combi-
nation of several components but can be taken from the
typical “gate charge” curve included on most data sheets
(Figure 9).
V IN
MILLER EFFECT
V GS
a b
+ DS
Q IN V GS
C MILLER = (Q B – Q A )/V DS –
3703 F09
Figure 9. Gate Charge Characteristic
The curve is generated by forcing a constant input cur-
rent into the gate of a common source, current source
loaded stage and then plotting the gate voltage versus
time. The initial slope is the effect of the gate-to-source
and the gate-to-drain capacitance. The flat portion of the
curve is the result of the Miller multiplication effect of the
drain-to-gate capacitance as the drain drops the voltage
across the current source load. The upper sloping line is
due to the drain-to-gate accumulation capacitance and
the gate-to-source capacitance. The Miller charge (the
increase in coulombs on the horizontal axis from a to b
while the curve is flat) is specified for a given V DS drain
voltage, but can be adjusted for different V DS voltages by
multiplying by the ratio of the application V DS to the curve
specified V DS values. A way to estimate the C MILLER term
is to take the change in gate charge from points a and b
on a manufacturers data sheet and divide by the stated
V DS voltage specified. C MILLER is the most important se-
lection criteria for determining the transition loss term in
the top MOSFET but is not directly specified on MOSFET
data sheets. C RSS and C OS are specified sometimes but
definitions of these parameters are not included.
When the controller is operating in continuous mode the
duty cycles for the top and bottom MOSFETs are given by:
Main Switch Duty Cycle =
Synchronous Switch Duty Cycle =
The power dissipation for the main and synchronous
MOSFETs at maximum output current are given by:
V OUT
V IN
I
2
? 1 1 ?
? + ? (f)
V ? V OUT
V IN
where δ is the temperature dependency of R DS(ON) , R DR
is the effective top driver resistance (approximately 2Ω at
V GS = V MILLER ), V IN is the drain potential and the change
in drain potential in the particular application. V TH(IL) is
the data sheet specified typical gate threshold voltage
specified in the power MOSFET data sheet at the specified
drain current. C MILLER is the calculated capacitance using
the gate charge curve from the MOSFET data sheet and
the technique described above.
Both MOSFETs have I 2 R losses while the topside N-channel
equation includes an additional term for transition losses,
which peak at the highest input voltage. For V IN < 25V,
the high current efficiency generally improves with larger
MOSFETs, while for V IN > 25V, the transition losses rapidly
increase to the point that the use of a higher R DS(ON) device
with lower C MILLER actually provides higher efficiency. The
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during
a short circuit when the synchronous switch is on close
to 100% of the period.
3703fc
14
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3704EMS#PBF | IC REG CTRLR INV PWM CM 10-MSOP |
| LTC3705IGN#TRPBF | IC CTRLR OCP 16SSOP |
| LTC3707IGN#TRPBF | IC REG CTRLR BUCK PWM CM 28-SSOP |
| LTC3708EUH#PBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| LTC3709EG#TRPBF | IC REG CTRLR BUCK PWM CM 36-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3704EMS | 功能描述:IC REG CTRLR INV PWM CM 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3704EMS#PBF | 功能描述:IC REG CTRLR INV PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3704EMS#PBF | 制造商:Linear Technology 功能描述:IC, DC/DC CONTROLLER, 300kHz, MSOP-10 |
| LTC3704EMS#TR | 功能描述:IC REG CTRLR INV PWM CM 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3704EMS#TRPBF | 功能描述:IC REG CTRLR INV PWM CM 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。