参数资料
| 型号： | LTC4101EG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/30页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR BATT CHRG 24-SSOP |
| 标准包装： | 59 |
| 功能： | 充电管理 |
| 电池化学： | 智能电池 |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC4101
OPERATION
to set the bottom MOSFET on time. The result is quasi-
constant frequency operation: the converter frequency
remains nearly constant over a wide range of output
voltages. This activity is diagrammed in Figure 3.
OFF
Charger Start-Up
When the charger is enabled, it will not begin switching
until the I TH voltage exceeds a threshold that assures initial
current will be positive. This threshold is 5% to 15% of the
maximum programmed current. After the charger begins
TGATE
ON
switching, the various loops will control the current at a
BGATE
ON
OFF
t OFF
TRIP POINT SET
level that is higher or lower than the initial current. The
duration of this transient condition depends upon the loop
compensation, but is typically less than 1ms.
BY I TH VOLTAGE
INDUCTOR
CURRENT
4101 F01
SMBus Interface
Figure 3.
The peak inductor current, at which I CMP resets the SR
latch, is controlled by the voltage on I TH . I TH is in turn
controlled by several loops, depending upon the situation
at hand. The average current control loop converts the
voltage between CSP and BAT to a representative current.
Error amp CA2 compares this current against the desired
current programmed by the I DAC at the I DC pin and adjusts
I TH for the desired voltage across R SENSE .
The voltage at BAT is divided down by an internal resis-
tor divider set by the V DAC and is used by error amp EA
to decrease I TH if the divider voltage is above the 1.19V
reference.
The ampli?er CL1 monitors and limits the input current,
normally from the AC adapter, to a preset level (100mV/R CL ).
At input current limit, CL1 will decrease the I TH voltage to
reduce charging current.
An overvoltage comparator, OV, guards against transient
overshoots (>7%). In this case, the top MOSFET is turned
off until the overvoltage condition is cleared. This feature
is useful for batteries that “load dump” themselves by
opening their protection switch to perform functions such
as calibration or pulse mode charging.
PWM Watchdog Timer
There is a watchdog timer that observes the activity on the
TGATE pin. If TGATE stops switching for more than 40μs,
the watchdog activates and turns off the top MOSFET for
about 400ns. The watchdog engages to prevent very low
frequency operation in dropout – a potential source of audible
noise when using ceramic input and output capacitors.
All communications over the SMBus are interpreted by the
SMBus interface block. The SMBus interface is a SMBus
slave device at address 0x12. All internal LTC4101 reg-
isters may be updated and accessed through the SMBus
interface, and charger controller as required. The SMBus
protocol is a derivative of the I 2 C bus (Reference “I 2 C-
Bus and How to Use It, V1.0” by Philips, and “System
Management Bus Speci?cation,” Version 1.1, from the
SBS Implementers Forum, for a complete description of
the bus protocol requirements.)
All data is clocked into the shift register on the rising edge
of SCL. All data is clocked out of the shift register on the
falling edge of SCL. Detection of an SMBus Stop condi-
tion, or power-on reset via the V DD power-fail, will reset
the SMBus interface to an initial state at any time.
The LTC4101 command set is interpreted by the SMBus
interface and passed onto the charger controller block as
control signals or updates to internal registers.
Description of Supported Battery Charger Functions
The functions are described as follows (see Table 1 also):
FunctionName() 'hnn (command code)
Description: A brief description of the function.
Purpose: The purpose of the function, and an example
where appropriate.
? SMBus Protocol: Refer to Section 5 of the Smart
Battery Charger speci?cation for more details.
*http://www.SBS-FORUM.org
4101fa
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
| LTC4160EUDC-1#TRPBF | IC SWITCH POWER MANAGER 20-QFN |
| LTC4410ES6#TRPBF | IC POWER MANAGER USB TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF#PBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4110EUHF#PBF | 制造商:Linear Technology 功能描述:Battery Management IC |
| LTC4110EUHF#TRPBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。