参数资料
| 型号： | LTC4101EG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/30页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR BATT CHRG 24-SSOP |
| 标准包装： | 59 |
| 功能： | 充电管理 |
| 电池化学： | 智能电池 |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC4101
OPERATION
table de?nes the maximum permissible value of CHARG-
ING_VOLTAGE that will not set the VOLTAGE_OR in the
ChargerStatus() function for a given value of R VLIM :
the LOWI current mode of the I DAC .
? SMBus Protocol: Write Word.
Input: The NO_LOWI is the only bit recognized by this
R ILIM
Short to GND
10kΩ ±1%
33kΩ ±1%
100kΩ ± 1%
Open (or short to V DD )
Maximum ChargingVoltage()
0x1090 (4240mV)
0x10D0 (4304mV)
0x1150 (4432mV)
0x11A0 (4512mV)
0x1580 (5504mV)
function. The default value of NO_LOWI is zero. The
LTC4101 LOWI current mode provides a more accurate
average charge current when the charge current is less
than 1/16 of the full-scale I DAC value. When the NO_LOWI
is set, a less accurate I DAC algorithm is used to generate
the charging current, but because the charger is not pulsed
on and off, it may be preferred.
AlarmWarning() ('h16)
Description: The Smart Battery, acting as a bus master
device, sends the AlarmWarning() message to the LTC4101
to notify it that one or more alarm conditions exist. Alarm
indications are encoded as bit ?elds in the Battery’s Status
register, which is then sent to the LTC4101 by this func-
tion.
Purpose: The LTC4101 will use the information sent by
this function to properly charge the battery. The LTC4101
will only respond to certain alarm bits. Writing to this
function does not necessarily cause an alarm condition
that inhibits battery charging.
? SMBus Protocol: Write Word.
Input: Only the OVER_CHARGED_ALARM, TERMINATE
_CHARGE_ALARM, reserved (0x2000), and OVER
_TEMP_ALARM bits are supported by the LTC4101.
Writing a one to any of these speci?ed bits will inhibit
the charging by the LTC4101 and will set the ALARM_
INHIBITED bit in the ChargerStatus() function. The
TERMINATE_DISCHARGE_ALARM, REMAINING_
CAPACITY_ALARM, REMAINING_TIME_ALARM, and the
ERROR bits are ignored by the LTC4101.
LTC0() ('h3C)
Description: The SMBus Host uses this command to
determine the version number of the LTC4101 and set
extended operation modes not de?ned by the Smart Bat-
tery Charger Speci?cation.
Purpose: This function allows the SMBus Host to deter-
mine if the battery charger is an LTC4101. Identifying the
manufacturer and version of the Smart Battery Charger
permits software to perform tasks speci?c to a given
? SMBus Protocol: Read Word.
Output: The NO_LOWI indicates the I DAC mode of opera-
tion. If clear, then the LOWI current mode will be used
when the charging current is less than 1/16 of the full-
scale I DAC value.
The LTC Version Identi?cation will always be 0x4040 for
the LTC4101.
Alert Response Address (ARA)
Description: The SMBus system host uses the Alert
Response Address to quickly identify the generator of an
SMBALERT# event.
Purpose: The LTC4101 will respond to an ARA address
0x18 if the SMBALERT signal is actively pulling down the
SMBALERT# bus. The LTC4101 will follow the prioritiza-
tion reporting as de?ned in the System Management Bus
Speci?cation, Version 1.1, from the SBS Implementers
Forum.
? SMBus Protocol: A 7-bit Addressable Device Re-
sponds to an ARA.
Output: The Device Address will be sent to the SMBus
system host. The LTC4101 Device address is 0x12.
The following events will cause the LTC4101 to pull-down
the SMBALERT# bus through the SMBALERT pin:
? Change of AC_PRESENT in the ChargerStatus() func-
tion.
? Change of BATTERY_PRESENT in the ChargerStatus()
function.
? Setting ALARM_INHIBITED in the ChargerStatus()
function.
charger. The LTC4101 also provides a means of disabling
? Internal power-on reset condition.
4101fa
15
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
| LTC4160EUDC-1#TRPBF | IC SWITCH POWER MANAGER 20-QFN |
| LTC4410ES6#TRPBF | IC POWER MANAGER USB TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF#PBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4110EUHF#PBF | 制造商:Linear Technology 功能描述:Battery Management IC |
| LTC4110EUHF#TRPBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。