参数资料
| 型号： | LTC4101EG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/30页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR BATT CHRG 24-SSOP |
| 标准包装： | 59 |
| 功能： | 充电管理 |
| 电池化学： | 智能电池 |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC4101
OPERATION
SMBus Accelerator Pull-Ups
Both SCL and SDA have SMBus accelerator circuits
which reduce the rise time on systems with signi?cant
capacitance on the two SMBus signals. The dynamic pull-up
circuitry detects a rising edge on SDA or SCL and applies
1mA to 10mA pull-up to V DD when V IN > 0.8V until V IN
< V DD – 0.8V (external pull-up resistors are still required
to supply DC current). This action allows the bus to meet
SMBus rise time requirements with as much as 250pF on
each SMBus signal. The improved rise time will bene?t
all of the devices which use the SMBus, especially those
devices that use the I 2 C logic levels. Note that the dynamic
pull-up circuits only pull to V DD , so some SMBus devices
that are not compliant to the SMBus speci?cations may still
have rise time compliance problems if the SMBus pull-up
resistors are terminated with voltages higher than V DD .
The Control Block
The LTC4101 charger operations are handled by the con-
trol block. This block is capable of charging the selected
battery autonomously or under SMBus Host control.
The control block can request communications with the
system management host (SMBus Host) by asserting
SMBALERT = 0; this will cause the SMBus Host, if present,
to poll the LTC4101.
The control block receives SMBus slave commands from
the SMBus interface block.
The control block allows the LTC4101 to meet the fol-
lowing Smart Battery-controlled (Level 2) charger
requirements:
1. Implements the Smart Battery’s critical warning mes-
sages over the SMBus.
2. Operates as an SMBus slave device that responds to
ChargingVoltage() and ChargingCurrent() commands and
adjusts the charger output parameters accordingly.
3. The host may control charging by disabling the Smart
Wake-up Charging Mode
The following conditions must be met in order to allow
wake-up charging of the battery:
1. The SafetySignal must be RES_COLD, RES_IDEAL, or
RES_UR.
2. AC must be present. This is quali?ed by DCDIV > V ACP .
Wake-up charging initiates when a newly inserted battery
does not send ChargingCurrent() and ChargingVoltage()
functions to the LTC4101.
The following conditions will terminate the Wake-up
Charging Mode.
1. A T TIMEOUT period is reached when the SafetySignal is
RES_COLD or RES_UR.
2. The SafetySignal is registering RES_OR.
3. The successful writing of the ChargingCurrent() AND
ChargingVoltage() function. The LTC4101 will proceed
to the controlled charging mode after these two func-
tions are written.
4. The SafetySignal is registering RES_HOT.
5. The AC power is no longer present. (DCDIV < V ACP )
6. The ALARM_INHIBITED becomes set in the Charger-
Status() function.
7. The INHIBIT_CHARGE is set in the ChargerMode()
function.
8. The CHGEN pin is pulled low by an external device. The
LTC4101 will resume wake-up charging, if the CHGEN
pin is released by the external device. Toggling the
CHGEN pin will not reset the T TIMEOUT timer.
9. There is insuf?cient DCIN voltage to charge the battery.
The LTC4101 will resume wake-up charging when there
is suf?cient DCIN voltage to charge the battery. This
condition will not reset the T TIMEOUT timer.
Battery’s ability to transmit ChargingCurrent() and
ChargingVoltage() request functions and broadcast-
ing the charging commands to the LTC4101 over the
SMBus.
4. The LTC4101 will still respond to Smart Battery critical
warning messages without host intervention.
4101fa
16
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
| LTC4160EUDC-1#TRPBF | IC SWITCH POWER MANAGER 20-QFN |
| LTC4410ES6#TRPBF | IC POWER MANAGER USB TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF#PBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4110EUHF#PBF | 制造商:Linear Technology 功能描述:Battery Management IC |
| LTC4110EUHF#TRPBF | 功能描述:IC BATTERY BACKUP MANAGER 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。