- 您现在的位置：买卖IC网 > PDF目录224121 > M25P10-AVMB6T/X (NUMONYX) FLASH 2.7V PROM, DSO8 PDF资料下载
参数资料
| 型号： | M25P10-AVMB6T/X |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | FLASH 2.7V PROM, DSO8 |
| 封装： | 2 X 3 MM, ROHS COMPLIANT, UFDFPN-8 |
| 文件页数： | 24/51页 |
| 文件大小： | 1103K |
| 代理商： | M25P10-AVMB6T/X |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
Instructions
M25P10-A
30/51
6.11
Deep Power-down (DP)
Executing the Deep Power-down (DP) instruction is the only way to put the device in the
lowest consumption mode (the Deep Power-down mode). It can also be used as a software
protection mechanism, while the device is not in active use, as in this mode, the device
ignores all write, program and erase instructions.
Driving Chip Select (S) High deselects the device, and puts the device in the Standby mode
(if there is no internal cycle currently in progress). But this mode is not the Deep Power-
down mode. The Deep Power-down mode can only be entered by executing the Deep
Power-down (DP) instruction, to reduce the standby current (from ICC1 to ICC2, as specified
in Table 14).
To take the device out of Deep Power-down mode, the Release from Deep Power-down and
Read Electronic Signature (RES) instruction must be issued. No other instruction must be
issued while the device is in Deep Power-down mode.
The Release from Deep Power-down, and Read Electronic Signature (RES) instruction and
the Read Identification (RDID) instruction also allow the electronic signature of the device to
be output on Serial Data output (Q).
The Deep Power-down mode automatically stops at power-down, and the device always
powers-up in the Standby mode.
The Deep Power-down (DP) instruction is entered by driving Chip Select (S) Low, followed
by the instruction code on Serial Data input (D). Chip Select (S) must be driven Low for the
entire duration of the sequence.
The instruction sequence is shown in Figure 17.
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Deep Power-down (DP) instruction is not executed. As soon as
Chip Select (S) is driven High, it requires a delay of tDP before the supply current is reduced
to ICC2 and the Deep Power-down mode is entered.
Any Deep Power-down (DP) instruction, while an Erase, Program or Write cycle is in
progress, is rejected without having any effects on the cycle that is in progress.
Figure 17.
Deep Power-down (DP) instruction sequence
C
D
AI03753D
S
2
1
34567
0
tDP
Deep Power-down mode
Standby mode
Instruction
相关PDF资料 |
PDF描述 |
|---|---|
| M25P10-AVME3 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P10-AVME3G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P10-AVME3P | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P10-AVME3T | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25P10-AVME3TG | 4 Mbit Uniform Sector, Serial Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M25P10-AVME3 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface |
| M25P10-AVME3G | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface |
| M25P10-AVME3P | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface |
| M25P10-AVME3T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface |
| M25P10-AVME3TG | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface |
发布紧急采购，3分钟左右您将得到回复。