- 您现在的位置：买卖IC网 > PDF目录180125 > M29W800FB9N3F (NUMONYX) 512K X 16 FLASH 3V PROM, 90 ns, PDSO48 PDF资料下载
参数资料
| 型号： | M29W800FB9N3F |
| 厂商： | NUMONYX |
| 元件分类： | PROM |
| 英文描述： | 512K X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| 封装： | 12 X 20 MM, ROHS COMPLIANT, PLASTIC, TSOP-48 |
| 文件页数： | 8/49页 |
| 文件大小： | 936K |
| 代理商： | M29W800FB9N3F |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Command interface
M29W800FT, M29W800FB
4
Command interface
All bus write operations to the memory are interpreted by the command interface.
Commands consist of one or more sequential bus write operations. Failure to observe a
valid sequence of bus write operations will result in the memory returning to read mode. The
long command sequences are imposed to maximize data security.
The address used for the commands changes depending on whether the memory is in 16-
used, for a summary of the commands.
4.1
Read/Reset command
The Read/Reset command returns the memory to its read mode where it behaves like a
ROM or EPROM, unless otherwise stated. It also resets the errors in the status register.
Either one or three bus write operations can be used to issue the Read/Reset command.
The Read/Reset command can be issued, between bus write cycles before the start of a
program or erase operation, to return the device to read mode. Once the program or erase
operation has started the Read/Reset command is no longer accepted. The Read/Reset
command will not abort an erase operation when issued while in erase suspend.
4.2
Auto Select command
The Auto Select command is used to read the manufacturer code, the device code and the
block protection status. Three consecutive bus write operations are required to issue the
Auto Select command. Once the Auto Select command is issued the memory remains in
auto select mode until a Read/Reset command is issued. Read CFI Query and Read/Reset
commands are accepted in auto select mode, all other commands are ignored.
From the auto select mode the manufacturer code can be read using a bus read operation
with A0 = VIL and A1 = VIL. The other address bits may be set to either VIL or VIH. The
manufacturer code for Numonyx is 0020h.
The device code can be read using a bus read operation with A0 = VIH and A1 = VIL. The
other address bits may be set to either VIL or VIH. The device code for the M29W800FT is
22D7h and for the M29W800FB is 225Bh.
The block protection status of each block can be read using a bus read operation with A0 =
VIL, A1 = VIH, and A12-A18 specifying the address of the block. The other address bits may
be set to either VIL or VIH. If the addressed block is protected then 01h is output on data
inputs/outputs DQ0-DQ7, otherwise 00h is output.
相关PDF资料 |
PDF描述 |
|---|---|
| M2CT-90A1-24ER | PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT-THREADED |
| M2S56D30AKT-75 | 32M X 8 DDR DRAM, 0.75 ns, PDSO64 |
| M2V56S30ATP-6 | 32M X 8 SYNCHRONOUS DRAM, 5.4 ns, PDSO54 |
| M30-6000206 | 2 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
| M30-6000406 | 4 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M29W800FT70D11 | 制造商:Micron Technology Inc 功能描述:PARALLEL NOR - Gel-pak, waffle pack, wafer, diced wafer on film |
| M29W800FT70N3E | 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TSOP |
| M29W800FT70N3F | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel |
| M29W800FT70N3F TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TSOP |
| M29W800FT70ZA3SE | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 8MBIT 70NS 48TFBGA |
发布紧急采购，3分钟左右您将得到回复。