- 您现在的位置：买卖IC网 > PDF目录67761 > M34519M8-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 PDF资料下载
参数资料
| 型号： | M34519M8-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| 封装： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件页数： | 75/138页 |
| 文件大小： | 1146K |
| 代理商： | M34519M8-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页当前第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页
4519 Group
Rev.3.01
2005.06.15
page 39 of 160
REJ03B0007-0301
(11) Timer input/output pin
(D6/CNTR0 pin, D7/CNTR1 pin)
CNTR0 pin is used to input the timer 1 count source and output the
timer 1 and timer 2 underflow signal divided by 2.
CNTR1 pin is used to input the timer 3 count source and output the
PWM signal generated by timer 4.
The D6/CNTR0 pin function can be selected by bit 0 of register W6.
The selection of D7/CNTR1 output signal can be controlled by bit 3
of register W4.
When the CNTR0 input is selected for timer 1 count source, timer
1 counts the rising or falling waveform of CNTR0 input. The count
edge is selected by the bit 2 of register W6.
When the CNTR1 input is selected for timer 3 count source, timer
3 counts the rising or falling waveform of CNTR1 input. The count
edge is selected by the bit 3 of register W6.
(12) PWM output function (D7/CNTR1, timer 3,
timer 4)
When bit 3 of register W4 is set to “1”, timer 4 reloads data from re-
load register R4L and R4H alternately each underflow.
Timer 4 generates the PWM signal (PWMOUT) of the “L” interval
set as reload register R4L, and the “H” interval set as reload regis-
ter R4H. The PWM signal (PWMOUT) is output from CNTR1 pin.
When bit 2 of register W4 is set to “1” at this time, the interval
(PWM signal “H” interval) set to reload register R4H for the counter
of timer 4 is extended for a half period of count source.
In this case, when a value set in reload register R4H is n, timer 4
divides the count source signal by n + 1.5 (n = 1 to 255).
When this function is used, set “1” or more to reload register R4H.
When bit 1 of register W6 is set to “1”, the PWM signal output to
CNTR1 pin is switched to valid/invalid each timer 3 underflow.
However, when timer 3 is stopped (bit 2 of register W3 is cleared to
“0”), this function is canceled.
Even when bit 1 of a register W4 is cleared to “0” in the “H” interval
of PWM signal, timer 4 does not stop until it next timer 4 underflow.
When clearing bit 1 of register W4 to “0” to stop timer 4 while the
PWM output function is used, avoid a timing when timer 4
underflows.
(9) Count start synchronization circuit (timer 1,
timer 3)
Timer 1 and timer 3 have the count start synchronous circuit which
synchronizes the input of INT0 pin and INT1 pin, and can start the
timer count operation.
Timer 1 count start synchronous circuit function is selected by set-
ting the bit 0 of register I1 to “1” and the control by INT0 pin input
can be performed.
Timer 3 count start synchronous circuit function is selected by set-
ting the bit 0 of register I2 to “1” and the control by INT1 pin input
can be performed.
When timer 1 or timer 3 count start synchronous circuit is used, the
count start synchronous circuit is set, the count source is input to
each timer by inputting valid waveform to INT0 pin or INT1 pin.
The valid waveform of INT0 pin or INT1 pin to set the count start
synchronous circuit is the same as the external interrupt activated
condition.
Once set, the count start synchronous circuit is cleared by clearing
the bit I10 or I20 to “0” or reset.
However, when the count auto-stop circuit is selected, the count
start synchronous circuit is cleared (auto-stop) at the timer 1 or
timer 3 underflow.
(10) Count auto-stop circuit (timer 1, timer 3)
Timer 1 has the count auto-stop circuit which is used to stop timer
1 automatically by the timer 1 underflow when the count start syn-
chronous circuit is used.
The count auto-stop cicuit is valid by setting the bit 3 of register W1
to “1”. It is cleared by the timer 1 underflow and the count source to
timer 1 is stopped.
This function is valid only when the timer 1 count start synchronous
circuit is selected.
Timer 3 has the count auto-stop circuit which is used to stop timer
3 automatically by the timer 3 underflow when the count start syn-
chronous circuit is used.
The count auto-stop cicuit is valid by setting the bit 3 of register W3
to “1”. It is cleared by the timer 3 underflow and the count source to
timer 3 is stopped.
This function is valid only when the timer 3 count start synchronous
circuit is selected.
相关PDF资料 |
PDF描述 |
|---|---|
| M34519M6-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34553M8H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34553M4-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34553G8HFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34553M4H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M34-52 | 制造商:GAMEWELL-FCI 制造商全称:GAMEWELL-FCI 功能描述:Three-Fold Fire Alarm Boxes and Transmitters |
| M34524EDFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34524M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34524MC-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 720 FAMILY / 4500 SERIES |
| M3452-C09K1 | 制造商:Bonitron 功能描述:OVERVOLTAGE BRAKING TRANSISTOR |
发布紧急采购，3分钟左右您将得到回复。