- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17007GTI+T (Maxim Integrated Products)IC CTRLR QPWM GRAPHICS 28TQFN PDF资料下载
参数资料
| 型号： | MAX17007GTI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/35页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR QPWM GRAPHICS 28TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Quick-PWM™ |
| 应用： | 电源 |
| 电流 - 电源： | 1.7mA |
| 电源电压： | 4.5 V ~ 26 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Dual and Combinable QPWM Graphics
Core Controllers for Notebook Computers
+5V Bias Supply (V CC , V DD )
The MAX17007/MAX17008 require an external 5V bias
supply in addition to the battery. Typically, this 5V bias
supply is the notebook’s 95%-efficient 5V system sup-
ply. Keeping the bias supply external to the IC improves
efficiency and eliminates the cost associated with the 5V
linear regulator that would otherwise be needed to sup-
ply the PWM circuit and gate drivers. If stand-alone
capability is needed, the 5V supply can be generated
with an external linear regulator such as the MAX1615.
The 5V bias supply powers both the PWM controllers
and internal gate-drive power, so the maximum current
drawn depends on the external MOSFET’s gate capaci-
tance, and the selected switching frequency:
I BIAS = I Q + f SW1 Q G(SMPS1) + f SW2 Q G(SMPS2)
= 4mA to 40mA (typ)
Bypass V CC with a 1μF or greater ceramic capacitor to
the analog ground. Bypass V DD with a 2.2μF or greater
2V Reference
The 2V reference is accurate to ±1% over temperature
and load, making REF useful as a precision system ref-
erence. Bypass REF to GND with a 2.2nF. The refer-
ence sources up to 100μA and sinks 10μA to support
external loads.
Combined-Mode Operation (FB2 = V CC )
Combined-mode operation allows the MAX17007/
MAX17008 to support even higher output currents by
sharing the load current between two phases, distribut-
ing the power dissipation over several power compo-
nents to improve the efficiency. The MAX17007/
MAX17008 are configured in combined mode by con-
necting FB2 to V CC . See Figure 2 for the combined-
mode standard application circuit.
Table 3 lists the pin function differences between com-
bined mode and separate mode. See the Pin Description
table for additional details.
ceramic capacitor to the power ground. V CC and V DD
should be separated with a 10 ? resistor (Figure 1).
Table 3. Pin Function in Combined and Separate Modes
PIN
FB2
COMBINED MODE
Connect to V CC to configure MAX17007/MAX17008 for
combined-mode operation
SEPARATE MODE
Connect to REF for preset 1.5V, or use a resistor-
divider to set the SMPS2 output voltage
REFIN1
Sets the combined output voltage—dynamic, fixed, and Sets the SMPS1 output voltage—dynamic, fixed,
preset voltages supported and preset voltages supported
EN1
EN2
PGOOD1
PGOOD2
TON1
TON2
ILIM1
ILIM2 (CCI)
SKIP
Enables/disables combined output
Not used; connect to GND
Power-good indicator for combined output voltage
Not used; can be left open
Sets the per-phase switching frequency for both SMPSs
Use the same resistor as TON1
Sets the per-phase current limit for both SMPSs
Current-balance integrator output; connect a capacitor
from CCI to the output
Only three distinct modes of operation; ultrasonic mode
not supported
Enables/disables SMPS1
Enables/disables SMPS2
Power-good indicator for SMPS1
Power-good indicator for SMPS2
Sets the switching frequency for SMPS1
Sets the switching frequency for SMPS2
Sets SMPS1 current limit
Sets SMPS2 current limit
Supports all four modes of operation
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1700EEE+T | IC REG BST SYNC ADJ 0.8A 16QSOP |
| MAX17010ETL+T | IC LCD DISPLAY BIAS 40-TQFN |
| MAX17014ETM+T | IC PWR SUPPLY MULT-OUTPUT 48TQFN |
| MAX17017GTM+ | IC PWR SUPPLY CONTROLLER 48TQFN |
| MAX17019ATM+T | IC VOLT CTRL QUAD OUT 48-TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17008GTI+ | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17008GTI+T | 功能描述:电压模式 PWM 控制器 QPWM Graphics Core Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17009GTL+ | 功能描述:其他电源管理 AMD Dual-Phase CPU Controller RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX17009GTL+T | 功能描述:其他电源管理 AMD Dual-Phase CPU Controller RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX1700EEE | 功能描述:直流/直流开关转换器 1-3 Cell 1A Step-Up DC/DC Converters RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。