- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17101ETJ+T (Maxim Integrated Products)IC REG CTRLR DIV PWM CM 32TQFNEP PDF资料下载
参数资料
| 型号： | MAX17101ETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/31页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DIV PWM CM 32TQFNEP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 3 |
| 频率 - 最大： | 500kHz |
| 电源电压： | 6 V ~ 24 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 是 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 85°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页
Dual Quick-PWM, Step-Down Controller
with Low-Power LDO, RTC Regulator
PD ( N H Re sistive ) = ? OUT ? ( I LOAD ) R DS ( O N )
? V OUT ( V IN ? V OUT ) ?
?
?
PD ( N H Switching ) = ?
?+
? ?
?
?
Unstable operation manifests itself in two related but
distinctly different ways: double-pulsing and fast-feed-
back loop instability. Double-pulsing occurs due to
noise on the output or because the ESR is so low that
there is not enough voltage ramp in the output voltage
signal. This “fools” the error comparator into triggering
a new cycle immediately after the 400ns minimum off-
time period has expired. Double-pulsing is more annoy-
ing than harmful, resulting in nothing worse than
increased output ripple. However, it can indicate the
possible presence of loop instability due to insufficient
ESR. Loop instability results in oscillations at the output
after line or load steps. Such perturbations are usually
damped, but can cause the output voltage to rise
above or fall below the tolerance limits.
The easiest method for checking stability is to apply a
very fast zero-to-max load transient and carefully
observe the output voltage ripple envelope for over-
shoot and ringing. It can help to simultaneously monitor
the inductor current with an AC current probe. Do not
allow more than one cycle of ringing after the initial
step-response under/overshoot.
Input Capacitor Selection
The input capacitor must meet the ripple current
requirement (I RMS ) imposed by the switching currents:
I RMS = I LOAD ? ?
V IN
For most applications, nontantalum chemistries (ceramic,
aluminum, or OS-CON) are preferred due to their resis-
tance to power-up surge currents typical of systems
with a mechanical switch or connector in series with the
input. If the MAX17101 is operated as the second stage
of a two-stage power conversion system, tantalum input
capacitors are acceptable. In either configuration,
choose a capacitor that has less than 10°C tempera-
ture rise at the RMS input current for optimal reliability
and lifetime.
Power-MOSFET Selection
Most of the following MOSFET guidelines focus on the
challenge of obtaining high load-current capability when
using high-voltage (> 20V) AC adapters. Low-current
applications usually require less attention.
The high-side MOSFET (N H ) must be able to dissipate
the resistive losses plus the switching losses at both
V IN(MIN) and V IN(MAX) . Ideally, the losses at V IN(MIN)
should be roughly equal to the losses at V IN(MAX) , with
lower losses in between. If the losses at V IN(MIN) are
significantly higher, consider increasing the size of N H .
Conversely, if the losses at V IN(MAX) are significantly
higher, consider reducing the size of N H . If V IN does
not vary over a wide range, maximum efficiency is
achieved by selecting a high-side MOSFET (N H ) that
has conduction losses equal to the switching losses.
Choose a low-side MOSFET (N L ) that has the lowest
possible on-resistance (R DS(ON) ), comes in a moder-
ate-sized package (i.e., 8-pin SO, DPAK, or D 2 PAK),
and is reasonably priced. Ensure that the MAX17101
DL_ gate driver can supply sufficient current to support
the gate charge and the current injected into the para-
sitic drain-to-gate capacitor caused by the high-side
MOSFET turning on; otherwise, cross-conduction prob-
lems can occur. Switching losses are not an issue for
the low-side MOSFET since it is a zero-voltage
switched device when used in the step-down topology.
Power-MOSFET Dissipation
Worst-case conduction losses occur at the duty factor
extremes. For the high-side MOSFET (N H ), the worst-
case power dissipation due to resistance occurs at
minimum input voltage:
? V ? 2
? V IN ?
Generally, use a small high-side MOSFET to reduce
switching losses at high input voltages. However, the
R DS(ON) required to stay within package power-dissi-
pation often limits how small the MOSFET can be. The
optimum occurs when the switching losses equal the
conduction (R DS(ON) ) losses. High-side switching loss-
es do not become an issue until the input is greater
than approximately 15V.
Calculating the power dissipation in high-side
MOSFETs (N H ) due to switching losses is difficult, since
it must allow for difficult-to-quantify factors that influ-
ence the turn-on and turn-off times. These factors
include the internal gate resistance, gate charge,
threshold voltage, source inductance, and PCB layout
characteristics. The following switching loss calculation
provides only a very rough estimate and is no substi-
tute for breadboard evaluation, preferably including
verification using a thermocouple mounted on N H :
? V (MAX ) I LOAD f SW Q G( SW) ?
? I GATE ?
? V IN 2 C OSS f SW ?
2
26
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17108ETI+T | IC LEVEL SHIFTER 10CH 28TQFN |
| MAX17112ETB+T | IC CONV DC-DC STEP UP 10TDFN |
| MAX17117ETJ+ | IC REG INTERNAL SW BOOST 32TQFN |
| MAX17120ETJ+ | IC DRVR SCAN TFT LDC 32-TQFN |
| MAX1714AEEP+T | IC REG CTRLR BUCK PWM CM 20-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17101K-SMP | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX17102ETM+ | 功能描述:其他电源管理 Boost Regulator w/Scan Driver Op Amp RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX17102ETM+T | 功能描述:其他电源管理 Boost Regulator w/Scan Driver Op Amp RoHS:否 制造商:Texas Instruments 输出电压范围: 输出电流:4 mA 输入电压范围:3 V to 3.6 V 输入电流: 功率耗散: 工作温度范围:- 40 C to + 110 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-48 封装:Reel |
| MAX17102EVKIT+ | 功能描述:电源管理IC开发工具 MAX17102 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17103ETJ+ | 功能描述:直流/直流开关转换器 DC/DC Converter w/Scan Driver VGL RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。