参数资料
| 型号： | MAX6852AEE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 20/32页 |
| 文件大小： | 0K |
| 描述： | IC VFD CTRLR MATRIX 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 显示器类型： | 真空荧光 (VF) |
| 配置： | 5 x 7（矩阵） |
| 接口： | 串行 |
| 电流 - 电源： | 3.5mA |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
4-Wire Interfaced, 5 ? 7 Matrix Vacuum-
Fluorescent Display Controller
The multiplex clock frequency determines the multiplex
scan rate and the blink timing. The display scan rate is
{OSC / 400 / (1 + grids register value)}. There are 400
OSC cycles per digit multiplex period. For example,
with OSC = 4MHz, each display digit is enabled for
100μs. For a 40-grid display tube (grids register value
= 39 or 0x27), the display scan rate is 250Hz.
The BLINK output is the selectable blink period clock. It
is nominally 0.5Hz or 1Hz (OSC = 4MHz). It is low dur-
ing the first half of the blink period, and high during the
second half. The PORT0 and PORT1 general-purpose
outputs may be programmed to be BLINK output.
Synchronize the BLINK timing if desired by setting the
T bit in the configuration register (Table 19).
The RC oscillator uses an external resistor R OSC and
an external capacitor C OSC to set the oscillator fre-
quency. R OSC connects from OSC2 to ground. C OSC
connects from OSC1 to ground. The recommended val-
ues of R OSC and C OSC set the oscillator to 4MHz,
which makes the BLINK frequencies 0.5Hz and 1 Hz:
f OSC = K F / (R OSC x [C OSC + C STRAY ]) MHz
where:
K F = 2320
The effective value of C OSC includes not only the actual
external capacitor used, but also the stray capacitance
from OSC1 to GND. This capacitance is usually in the
1pF-to-5pF range, depending on the layout used.
The allowed range of f OSC is 2MHz to 8MHz. If f OSC is
set too high, the internal oscillator can stop working. An
internal fail-safe circuit monitors the multiplex clock and
detects a slow or nonworking multiplex clock. When a
slow or nonworking multiplex clock is detected, an
internal fail-safe oscillator generates a replacement
clock of about 200kHz. This backup clock ensures that
the VFD is not damaged by the multiplex operation halt-
ing inadvertently. The scan rate for 16 digits is about
15Hz in fail-safe mode, and the display flickers. A flick-
ering display is a good indication that there is a prob-
lem with the multiplex clock.
Power Supplies
The MAX6852 operates from a single 2.7V to 3.6V
power supply. Bypass the power supply to GND with a
0.1μF capacitor as close to the device as possible. Add
a bulk capacitor (such as a low-cost electrolytic 1μF to
22μF) if the MAX6852 is driving high current from any of
the general-purpose output ports.
R OSC = external resistor in k ? (allowable range 8k ? to
80k ? )
C OSC = external capacitor in pF
C STRAY = stray capacitance from OSC1 to GND in pF,
typically 2pF
For OSC = 4MHz, R OSC is 10k ? and C OSC is 56pF.
Table 8. Memory Mapping of User-Defined Font Register 0x05
COMMAND
ADDRESS
0x85
0x05
0x05
REGISTER
DATA
0x00 – 0x7F
0x00 – 0x7F
0x80 – 0xFF
READ OR
WRITE
Read
Write
Write
FUNCTION
Read 7-bit user-definable font data entry from current font address. MSB of the
register data is clear. Font address pointer is incremented after the read.
Write 7-bit user-definable font data entry to current font address. Font address
pointer is incremented after the write.
Write font address pointer with the register data.
Table 9. Font Pointer Address Behavior
FONT POINTER
ADDRESS
0x80 to 0xF6
0xF7
0xF8 to 0xFF
ACTION
Valid range to set the font address pointer. Pointer autoincrements after a font data read or write, while pointer
address remains in this range.
Further font data is ignored after a font data read or write to this pointer address.
Invalid range to set the font address pointer. Pointer is set to 0x80.
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX685ETG+ | IC REG BOOST INV ADJ 10MA 24TQFN |
| MAX6868UK46D6L+T | IC MPU SUPERVISOR SOT23-5 |
| MAX686EEE | IC REG BOOST INV +/-27.5V 16QSOP |
| MAX6871ETJ+ | IC SEQUENCE/SUPERVISOR 32TQFN |
| MAX6872ETJ+ | IC SEQUENCE/SUPERVISOR 32TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6853AEE | 功能描述:VFD驱动器 RoHS:否 制造商:Maxim Integrated 工作电源电压:8 V to 76 V, 3 V to 5.5 V 电源电流:0.9 mA, 700 uA 最大工作温度:+ 125 C 封装 / 箱体:SOIC-20 封装:Tube |
| MAX6853AEE+T | 功能描述:VFD驱动器 RoHS:否 制造商:Maxim Integrated 工作电源电压:8 V to 76 V, 3 V to 5.5 V 电源电流:0.9 mA, 700 uA 最大工作温度:+ 125 C 封装 / 箱体:SOIC-20 封装:Tube |
| MAX6853AEE-T | 功能描述:VFD驱动器 RoHS:否 制造商:Maxim Integrated 工作电源电压:8 V to 76 V, 3 V to 5.5 V 电源电流:0.9 mA, 700 uA 最大工作温度:+ 125 C 封装 / 箱体:SOIC-20 封装:Tube |
| MAX6854UK16D1+T | 功能描述:监控电路 Single nPower Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6854UK16D1-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。