- 您现在的位置：买卖IC网 > PDF目录18737 > MAX7032ATJ+T (Maxim Integrated)IC TRASCEIVER ASK/FSK 32TQFN PDF资料下载
参数资料
| 型号： | MAX7032ATJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 13/32页 |
| 文件大小： | 0K |
| 描述： | IC TRASCEIVER ASK/FSK 32TQFN |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 300MHz ~ 450MHz |
| 数据传输率 - 最大： | 33kbps |
| 调制或协议： | ASK，FSK，OOK |
| 应用： | 车库门开启器，遥控，双向 RKE |
| 功率 - 输出： | 10dBm |
| 灵敏度： | -114dBm |
| 电源电压： | 2.1 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 电流 - 接收： | 6.7mA |
| 电流 - 传输： | 12.5mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Low-Cost, Crystal-Based, Programmable,
ASK/FSK Transceiver with Fractional-N PLL
Pin Description (continued)
PIN
27
28
29
30
31
32
—
NAME
HVIN
CS
DIO
SCLK
XTAL1
XTAL2
EP
FUNCTION
High-Voltage Supply Input. For 3V operation, connect HVIN to PAVDD, AVDD, and DVDD. For 5V
operation, connect only HVIN to 5V. Bypass HVIN to GND with 0.01μF and 220pF capacitors placed
as close as possible to the pin.
Serial Interface Active-Low Chip Select
Serial Interface Serial Data Input/Output
Serial Interface Clock Input
Crystal Input 1. Bypass to GND if XTAL2 is driven by an AC-coupled external reference.
Crystal Input 2. XTAL2 can be driven from an AC-coupled external reference.
Exposed Pad. Solder evenly to the board’s ground plane for proper operation.
Detailed Description
The MAX7032 300MHz to 450MHz CMOS transceiver
and a few external components provide a complete
f =
1
2 π L TOTAL × C TOTAL
transmit and receive chain from the antenna to the digi-
tal data interface. This device is designed for transmit-
ting and receiving ASK and FSK data. All transmit
frequencies are generated by a fractional-N-based syn-
thesizer, allowing for very fine frequency steps in incre-
ments of f XTAL /4096. The receive LO is generated by a
traditional integer-N-based synthesizer. Depending on
component selection, data rates as high as 33kbps
(Manchester encoded) or 66kbps (NRZ encoded) can
be achieved.
Receiver
Low-Noise Amplifier (LNA)
The LNA is a cascode amplifier with off-chip inductive
degeneration that achieves approximately 30dB of volt-
age gain that is dependent on both the antenna match-
ing network at the LNA input and the LC tank network
between the LNA output and the mixer inputs.
The off-chip inductive degeneration is achieved by
connecting an inductor from LNASRC to GND. This
inductor sets the real part of the input impedance at
LNAIN, allowing for a more flexible match for low-input
impedance such as a PCB trace antenna. A nominal
value for this inductor with a 50 Ω input impedance is
12nH at 315MHz and 10nH at 434MHz, but the induc-
tance is affected by PCB trace length. LNASRC can be
shorted to ground to increase sensitivity by approxi-
mately 1dB, but the input match must then be reopti-
mized.
The LC tank filter connected to LNAOUT consists of L5
and C9 (see the Typical Application Circuit). Select L5
and C9 to resonate at the desired RF input frequency.
The resonant frequency is given by:
where L TOTAL = L5 + L PARASITICS and C TOTAL = C9 +
C PARASITICS .
L PARASITICS and C PARASITICS include inductance and
capacitance of the PCB traces, package pins, mixer
input impedance, LNA output impedance, etc. These
parasitics at high frequencies cannot be ignored and
can have a dramatic effect on the tank filter center fre-
quency. Lab experimentation must be done to optimize
the center frequency of the tank. The total parasitic
capacitance is generally between 5pF and 7pF.
Automatic Gain Control (AGC)
When the AGC is enabled, it monitors the RSSI output.
When the RSSI output reaches 1.28V, which corre-
sponds to an RF input level of approximately -55dBm,
the AGC switches on the LNA gain-reduction attenua-
tor. The attenuator reduces the LNA gain by 36dB,
thereby reducing the RSSI output by about 540mV to
740mV. The LNA resumes high-gain mode when the
RSSI output level drops back below 680mV (approxi-
mately -59dBm at the RF input) for a programmable
interval called the AGC dwell time. The AGC has a hys-
teresis of approximately 4dB. With the AGC function,
the RSSI dynamic range is increased, allowing the
MAX7032 to reliably produce an ASK output for RF
input levels up to 0dBm with a modulation depth of
18dB. AGC is not required and can be disabled in
either ASK or FSK mode. AGC is not necessary for FSK
mode because large received signal levels do not
affect FSK performance.
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| 7C-25.000MBB-T | OSC 25.000 MHZ 3.3V SMD |
| MAX2831ETM+T | IC TXRX 2.4GHZ-2.5GHZ 48TQFN |
| X-10GQ | SWITCH BASIC PNL MT 10A SOLDER |
| B82802A0030A220 | TRANSFORMER FLYBACK 36-60V SMD |
| MAX7030LATJ+T | IC ASK TXRX 315MHZ 32-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7032ETJ | 制造商:Maxim Integrated Products 功能描述: |
| MAX7032EVKIT-315 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7032EVKIT-433 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7032EVSYS-315 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7032EVSYS-433 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。