- 您现在的位置：买卖IC网 > PDF目录18737 > MAX7032ATJ+T (Maxim Integrated)IC TRASCEIVER ASK/FSK 32TQFN PDF资料下载
参数资料
| 型号： | MAX7032ATJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 27/32页 |
| 文件大小： | 0K |
| 描述： | IC TRASCEIVER ASK/FSK 32TQFN |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 300MHz ~ 450MHz |
| 数据传输率 - 最大： | 33kbps |
| 调制或协议： | ASK，FSK，OOK |
| 应用： | 车库门开启器，遥控，双向 RKE |
| 功率 - 输出： | 10dBm |
| 灵敏度： | -114dBm |
| 电源电压： | 2.1 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 电流 - 接收： | 6.7mA |
| 电流 - 传输： | 12.5mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页
Low-Cost, Crystal-Based, Programmable,
ASK/FSK Transceiver with Fractional-N PLL
Table 15. On-Timer (t ON ) Configuration
MIN t ON
MAX t ON
ONPS1
ONPS0
t ON TIME BASE
REG 0x0B = 0x00
REG 0x0B = 0xFF
REG 0x0C = 0x01
REG 0x0C = 0xFF
0
0
1
1
0
1
0
1
120μs
480μs
1920μs
7680μs
120μs
480μs
1.92ms
7.68ms
7.86s
31.46s
2min 6s
8min 23s
On Timer (t ON )
The on timer, t ON (see Figure 10), is a 16-bit timer that
is configured through register 0x0B for the upper byte,
register 0x0C for the lower byte (Table 15). The infor-
mation stored in this timer provides an additional way to
control the duration of the on time of the receiver.
The CPU must begin driving DIO low any time during
t LOW = t CPU + t RF + t ON . If the CPU fails to drive DIO
low at the end of t ON , DIO is pulled high through the
internal pullup resistor and the time sequence is restart-
ed, leaving the MAX7032 powered down. Any time the
DIO line is driven high while the DRX = 1, the DRX
sequence is initiated, as defined in Figure 10. In the
event that the CPU is processing data, after t ON
expires, the CPU should keep the MAX7032 awake by
holding the DIO line low.
The data written to the t ON register (register 0x0B and
register 0x0C) are multiplied by the t ON time base
(Table 15) to give the total t ON time. See the example in
the Off Timer (t OFF ) section. On power-up, the on-timer
register is reset to zero and must be written before
using DRX mode.
Transmitter Low-Frequency Register (TxLOW)
The TxLOW register sets the divider information of the
fractional-N synthesizer for the lower transmit frequency
in FSK mode. See the example given in the Fractional-N
PLL section. In ASK mode, TxLOW determines the carri-
er frequency.
Transmitter High-Frequency Register (TxHIGH)
The TxHIGH register sets the divider information of the
fractional-N synthesizer for the upper transmit frequency
in the FSK mode. In ASK mode, the content of TxHIGH
is not used. The 16-bit register contains the binary rep-
resentation of the TX PLL divider ratio, which is shown in
the example in the Fractional-N PLL section.
Applications Information
Output Matching to 50 Ω
When matched to a 50 Ω system, the MAX7032’s PA is
capable of delivering +10dBm of output power at V DD
= +2.7V. The output of the PA is an open-drain transis-
tor that requires external impedance matching and
pullup inductance for proper biasing. The pullup induc-
tance from the PA to PAV DD serves three main purpos-
es: it resonates the capacitive PA output, provides
biasing for the PA, and becomes a high-frequency
choke to prevent RF energy from coupling into V DD .
The network also forms a bandpass filter that provides
attention for the higher order harmonics.
Output Matching to PCB Loop Antenna
In most applications, the MAX7032 must be impedance
matched to a small-loop antenna. The antenna is usual-
ly fabricated out of a copper trace on a PCB in a rec-
tangular, circular, or square pattern. The antenna has
an impedance that consists of a lossy component and
a radiative component. To achieve high radiating effi-
ciency, the radiative component should be as high as
possible, while minimizing the lossy component. In
addition, the loop antenna has an inherent loop induc-
tance associated with it (assuming the antenna is termi-
nated to ground). For example, in a typical application,
the radiative impedance is less than 0.5 Ω , the lossy
impedance is less than 0.7 Ω , and the inductance is
approximately 50nH to 100nH.
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. On high-frequency inputs and
outputs, use controlled-impedance lines and keep
them as short as possible to minimize losses and radia-
tion. At high frequencies, trace lengths that are on the
order of λ /10 or longer act as antennas, where λ is the
wavelength.
______________________________________________________________________________________
27
相关PDF资料 |
PDF描述 |
|---|---|
| 7C-25.000MBB-T | OSC 25.000 MHZ 3.3V SMD |
| MAX2831ETM+T | IC TXRX 2.4GHZ-2.5GHZ 48TQFN |
| X-10GQ | SWITCH BASIC PNL MT 10A SOLDER |
| B82802A0030A220 | TRANSFORMER FLYBACK 36-60V SMD |
| MAX7030LATJ+T | IC ASK TXRX 315MHZ 32-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX7032ETJ | 制造商:Maxim Integrated Products 功能描述: |
| MAX7032EVKIT-315 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7032EVKIT-433 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7032EVSYS-315 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX7032EVSYS-433 | 功能描述:射频开发工具 MAX7032 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。