- 您现在的位置：买卖IC网 > PDF目录132984 > MB9AF311MPMC 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | MB9AF311MPMC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80 |
| 封装： | 0.50 MM PITCH, PLASTIC, LQFP-80 |
| 文件页数： | 45/114页 |
| 文件大小： | 1357K |
| 代理商： | MB9AF311MPMC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页当前第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
36
10.2
BOD Disable(1)
When the brown-out detector (BOD) is enabled by BODLEVEL fuses - see Table 28-6 on page 253 and onwards, the BOD is
actively monitoring the power supply voltage during a sleep period. To save power, it is possible to disable the BOD by
software for some of the sleep modes, see Table 10-1 on page 35. The sleep mode power consumption will then be at the
same level as when BOD is globally disabled by fuses. If BOD is disabled in software, the BOD function is turned off
immediately after entering the sleep mode. Upon wake-up from sleep, BOD is automatically enabled again. This ensures
safe operation in case the VCC level has dropped during the sleep period.
When the BOD has been disabled, the wake-up time from sleep mode will be approximately 60 s to ensure that the BOD is
working correctly before the MCU continues executing code.
BOD disable is controlled by bit 6, BODS (BOD Sleep) in the control register MCUCR, see
Section 10.11.2 “MCUCR – MCU Control Register” on page 39. Writing this bit to one turns off the BOD in relevant sleep
modes, while a zero in this bit keeps BOD active. Default setting keeps BOD active, i.e. BODS set to zero.
Writing to the BODS bit is controlled by a timed sequence and an enable bit, see
Note:
1.
BOD disable only available in picoPower devices ATmega48PA/88PA/168PA
10.3
Idle Mode
When the SM2...0 bits are written to 000, the SLEEP instruction makes the MCU enter Idle mode, stopping the CPU but
allowing the SPI, USART, analog comparator, ADC, 2-wire serial interface, Timer/Counters, watchdog, and the interrupt
system to continue operating. This sleep mode basically halts clkCPU and clkFLASH, while allowing the other clocks to run.
Idle mode enables the MCU to wake up from external triggered interrupts as well as internal ones like the timer overflow and
USART transmit complete interrupts. If wake-up from the analog comparator interrupt is not required, the analog comparator
can be powered down by setting the ACD bit in the analog comparator control and status register – ACSR. This will reduce
power consumption in Idle mode. If the ADC is enabled, a conversion starts automatically when this mode is entered.
10.4
ADC Noise Reduction Mode
When the SM2...0 bits are written to 001, the SLEEP instruction makes the MCU enter ADC noise reduction mode, stopping
the CPU but allowing the ADC, the external interrupts, the 2-wire serial interface address watch, Timer/Counter2(1), and the
watchdog to continue operating (if enabled). This sleep mode basically halts clkI/O, clkCPU, and clkFLASH, while allowing the
other clocks to run.
This improves the noise environment for the ADC, enabling higher resolution measurements. If the ADC is enabled, a
conversion starts automatically when this mode is entered. Apart from the ADC conversion complete interrupt, only an
external reset, a watchdog system reset, a watchdog interrupt, a brown-out reset, a 2-wire serial interface address match, a
Timer/Counter2 interrupt, an SPM/EEPROM ready interrupt, an external level interrupt on INT0 or INT1 or a pin change
interrupt can wake up the MCU from ADC noise reduction mode.
Notes: 1.
Timer/Counter2 will only keep running in asynchronous mode, see
10.5
Power-down Mode
When the SM2...0 bits are written to 010, the SLEEP instruction makes the MCU enter power-down mode. In this mode, the
external oscillator is stopped, while the external interrupts, the 2-wire serial interface address watch, and the watchdog
continue operating (if enabled). Only an external reset, a watchdog system reset, a watchdog interrupt, a brown-out reset, a
2-wire serial interface address match, an external level interrupt on INT0 or INT1, or a pin change interrupt can wake up the
MCU. This sleep mode basically halts all generated clocks, allowing operation of asynchronous modules only.
Note:
If a level triggered interrupt is used for wake-up from power-down, the required level must be held long enough
for the MCU to complete the wake-up to trigger the level interrupt. If the level disappears before the end of the
start-up time, the MCU will still wake up, but no interrupt will be generated.
Section 13. “External Interrupts” on page 59. The start-up time is defined by the SUT and CKSEL Fuses as
described in Section 9. “System Clock and Clock Options” on page 24.
When waking up from power-down mode, there is a delay from the wake-up condition occurs until the wake-up becomes
effective. This allows the clock to restart and become stable after having been stopped. The wake-up period is defined by the
same CKSEL fuses that define the reset time-out period, as described in Section 9.2 “Clock Sources” on page 25.
相关PDF资料 |
PDF描述 |
|---|---|
| MSP430G2152IRSA16 | 16-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQCC16 |
| M37704E2EFP | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| MSM65544-JS | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQCC68 |
| MSM65516SS | 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64 |
| MSM65P512JS | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MB9AF312KPMC1-G-JNE2 | 功能描述:ARM? Cortex?-M3 FM3 MB9A310K Microcontroller IC 32-Bit 40MHz 160KB (160K x 8) FLASH 52-LQFP (10x10) 制造商:cypress semiconductor corp 系列:FM3 MB9A310K 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO，I2C，LIN，UART/USART，USB 外设:DMA，LVD，POR，PWM，WDT I/O 数:36 程序存储容量:160KB（160K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:16K x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 8x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:52-LQFP 供应商器件封装:52-LQFP（10x10） 标准包装:160 |
| MB9AF312KPMC-ES-E1 | 制造商:FUJITSU 功能描述: |
| MB9AF312KPMC-G-JNE1 | 制造商:FUJITSU 功能描述: |
| MB9AF312KPMC-G-JNE2 | 功能描述:ARM? Cortex?-M3 FM3 MB9A310K Microcontroller IC 32-Bit 40MHz 160KB (160K x 8) FLASH 48-LQFP (7x7) 制造商:cypress semiconductor corp 系列:FM3 MB9A310K 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO，I2C，LIN，UART/USART，USB 外设:DMA，LVD，POR，PWM，WDT I/O 数:36 程序存储容量:160KB（160K x 8） 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:16K x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 8x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C（TA） 封装/外壳:48-LQFP 供应商器件封装:48-LQFP（7x7） 标准包装:250 |
| MB9AF312KQN-ES-AWE2 | 制造商:FUJITSU 功能描述: |
发布紧急采购，3分钟左右您将得到回复。