参数资料
型号: MB9AF311MPMC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, FLASH, 40 MHz, RISC MICROCONTROLLER, PQFP80
封装: 0.50 MM PITCH, PLASTIC, LQFP-80
文件页数: 96/114页
文件大小: 1357K
代理商: MB9AF311MPMC
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
82
15.2.1 Definitions
Many register and bit references in this section are written in general form. A lower case “n” replaces the Timer/Counter
number, in this case 0. A lower case “x” replaces the output compare Unit, in this case compare unit A or compare unit B.
However, when using the register or bit defines in a program, the precise form must be used, i.e., TCNT0 for accessing
Timer/Counter0 counter value and so on.
The definitions in Table 15-1 are also used extensively throughout the document.
15.2.2 Registers
The Timer/Counter (TCNT0) and output compare registers (OCR0A and OCR0B) are 8-bit registers. Interrupt request
(abbreviated to Int.Req. in the figure) signals are all visible in the timer interrupt flag register (TIFR0). All interrupts are
individually masked with the timer interrupt mask register (TIMSK0). TIFR0 and TIMSK0 are not shown in the figure.
The Timer/Counter can be clocked internally, via the prescaler, or by an external clock source on the T0 pin. The clock select
logic block controls which clock source and edge the Timer/Counter uses to increment (or decrement) its value. The
Timer/Counter is inactive when no clock source is selected. The output from the clock select logic is referred to as the timer
clock (clkT0).
The double buffered output compare registers (OCR0A and OCR0B) are compared with the Timer/Counter value at all
times. The result of the compare can be used by the waveform generator to generate a PWM or variable frequency output on
the output compare pins (OC0A and OC0B). See Section 16.7.3 “Using the Output Compare Unit” on page 107 for details.
The compare match event will also set the compare flag (OCF0A or OCF0B) which can be used to generate an output
compare interrupt request.
15.3
Timer/Counter Clock Sources
The Timer/Counter can be clocked by an internal or an external clock source. The clock source is selected by the clock
select logic which is controlled by the clock select (CS02:0) bits located in the Timer/Counter control register (TCCR0B). For
Table 15-1. Definitions
Parameter
Definition
BOTTOM
The counter reaches the BOTTOM when it becomes 0x00.
MAX
The counter reaches its MAXimum when it becomes 0xFF (decimal 255).
TOP
The counter reaches the TOP when it becomes equal to the highest value in the count sequence. The
TOP value can be assigned to be the fixed value 0xFF (MAX) or the value stored in the OCR0A register.
The assignment is dependent on the mode of operation.
相关PDF资料
PDF描述
MSP430G2152IRSA16 16-BIT, FLASH, 16 MHz, RISC MICROCONTROLLER, PQCC16
M37704E2EFP 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80
MSM65544-JS 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQCC68
MSM65516SS 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PDIP64
MSM65P512JS 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQCC44
相关代理商/技术参数
参数描述
MB9AF312KPMC1-G-JNE2 功能描述:ARM? Cortex?-M3 FM3 MB9A310K Microcontroller IC 32-Bit 40MHz 160KB (160K x 8) FLASH 52-LQFP (10x10) 制造商:cypress semiconductor corp 系列:FM3 MB9A310K 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO,I2C,LIN,UART/USART,USB 外设:DMA,LVD,POR,PWM,WDT I/O 数:36 程序存储容量:160KB(160K x 8) 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:16K x 8 电压 - 电源(Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 8x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C(TA) 封装/外壳:52-LQFP 供应商器件封装:52-LQFP(10x10) 标准包装:160
MB9AF312KPMC-ES-E1 制造商:FUJITSU 功能描述:
MB9AF312KPMC-G-JNE1 制造商:FUJITSU 功能描述:
MB9AF312KPMC-G-JNE2 功能描述:ARM? Cortex?-M3 FM3 MB9A310K Microcontroller IC 32-Bit 40MHz 160KB (160K x 8) FLASH 48-LQFP (7x7) 制造商:cypress semiconductor corp 系列:FM3 MB9A310K 包装:托盘 零件状态:有效 核心处理器:ARM? Cortex?-M3 核心尺寸:32-位 速度:40MHz 连接性:CSIO,I2C,LIN,UART/USART,USB 外设:DMA,LVD,POR,PWM,WDT I/O 数:36 程序存储容量:160KB(160K x 8) 程序存储器类型:闪存 EEPROM 容量:- RAM 容量:16K x 8 电压 - 电源(Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 8x12b 振荡器类型:内部 工作温度:-40°C ~ 105°C(TA) 封装/外壳:48-LQFP 供应商器件封装:48-LQFP(7x7) 标准包装:250
MB9AF312KQN-ES-AWE2 制造商:FUJITSU 功能描述: