- 您现在的位置：买卖IC网 > PDF目录16588 > MC13892VLR2 (Freescale Semiconductor)IC PMU I.MX51/37/35/27 186MAPBGA PDF资料下载
参数资料
| 型号： | MC13892VLR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 107/158页 |
| 文件大小： | 0K |
| 描述： | IC PMU I.MX51/37/35/27 186MAPBGA |
| 标准包装： | 1,000 |
| 应用： | 电池管理，显示器（LED 驱动器），手持/移动设备，电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 186-LFBGA |
| 供应商设备封装： | 186-PBGA（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页当前第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DEVICE OPERATION
ADC SUBSYSTEM
TOUCH SCREEN INTERFACE
The touch screen interface provides all circuitry required for the readout of a 4-wire resistive touch screen. The touch screen
X plate is connected to TSX1 and TSX2 while the Y plate is connected to TSY1 and TSY2. A local supply TSREF will serve as
a reference. Several readout possibilities are offered.
In order to use the ADC inputs and properly convert and readout the values, the bit ADSEL should be set to a 1. This is valid
for touch screen readings as well as for general purpose reading on the same inputs.
The touch screen operating modes are configured via the TSMOD[2:0] bits show in the following table.
Table 95. Touch Screen Operating Mode
TSMOD2
x
0
1
0
1
TSMOD1
0
0
0
1
1
TSMOD0
0
1
1
x
x
Mode
Inactive
Interrupt
Reserved
Touch Screen
Reserved
Description
Inputs TSX1, TSX2, TSY1, TSY2 can be used as general purpose ADC inputs
Interrupt detection is active. Generates an interrupt TSI when plates make
contact. TSI is dual edge sensitive and 30 ms debounced
Reserved for a different interrupt mode
ADC will control a sequential reading of 2 times a XY coordinate pair and 2 times
a contact resistance
Reserved for a different reading mode
In inactive mode, the inputs TSX1, TSX2, TSY1, and TSY2 can be used as general purpose inputs. They are respectively
mapped on ADC channels 4, 5, 6, and 7.
In interrupt mode, a voltage is applied to the X-plate (TSX2) via a weak current source to VCORE, while the Y-plate is
connected to ground (TSY1). When the two plates make contact both will be at a low potential. This will generate a pen interrupt
to the processor. This detection does not make use of the ADC core or the TSREF regulator, so both can remain disabled.
In touch screen mode, the XY coordinate pairs and the contact resistance are read.
The X-coordinate is determined by applying TSREF over the TSX1 and TSX2 pins while performing a high-impedance reading
on the Y-plate through TSY1. The Y coordinate is determined by applying TSREF between TSY1 and TSY2, while reading the
TSX1 pin.
The contact resistance is measured by applying a known current into the TSY1 terminal of the touch screen and through the
terminal TSX2, which is grounded. The voltage difference between the two remaining terminals TSY2 and TSX1 is measured by
the ADC, and equals the voltage across the contact resistance. Measuring the contact resistance helps in determining if the touch
screen is touched with a finger or stylus.
To perform touch screen readings, the processor will have to select the touch screen mode, program the delay between the
conversions via the ATO and ATOX settings, trigger the ADC via one of the trigger sources, wait for an interrupt indicating the
conversion is done, and then read out the data. In order to reduce the interrupt rate and to allow for easier noise rejection, the
touch screen readings are repeated in the readout sequence.
Table 96. Touch Screen Reading Sequence
ADC Conversion
0
1
2
3
4
5
6
7
Signals sampled
X position
X position
Dummy
Y position
Y position
Dummy
Contact resistance
Contact resistance
Readout Address (85)
000
001
010
011
100
101
110
111
Notes
85. Address as indicated by ADA1[2:0] and ADA2[2:0]
The dummy conversion inserted between the different readings is to allow the references in the system to be pre-biased for
the change in touch screen plate polarity and will read out as '0'.
MC13892
Analog Integrated Circuit Device Data
Freescale Semiconductor
107
相关PDF资料 |
PDF描述 |
|---|---|
| RCA18DTMD | CONN EDGECARD 36POS R/A .125 SLD |
| EVAL-ADG2108EBZ | BOARD EVAL FOR ADG2108 |
| RCA18DTBN | CONN EDGECARD 36POS R/A .125 SLD |
| RCA18DTBH | CONN EDGECARD 36POS R/A .125 SLD |
| GBM28DCMN | CONN EDGECARD 56POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC1-38RX | 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL |
| MC1391 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TV HORIZONTAL PROCESSOR |
| MC13917-1900EVK | 功能描述:射频开发工具 MC13917_1900_EVK RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MC13917-350EVK | 功能描述:射频开发工具 MC13917_350_EVK RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MC13917-434EVK | 功能描述:射频开发工具 MC13917 EVB 434MHZ RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。