- 您现在的位置：买卖IC网 > PDF目录16588 > MC13892VLR2 (Freescale Semiconductor)IC PMU I.MX51/37/35/27 186MAPBGA PDF资料下载
参数资料
| 型号： | MC13892VLR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 36/158页 |
| 文件大小： | 0K |
| 描述： | IC PMU I.MX51/37/35/27 186MAPBGA |
| 标准包装： | 1,000 |
| 应用： | 电池管理，显示器（LED 驱动器），手持/移动设备，电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 186-LFBGA |
| 供应商设备封装： | 186-PBGA（12x12） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
CONTROL LOGIC
LICELL
Coin cell supply input and charger output. The LICELL pin provides a connection for a coin cell backup battery or supercap.
If the main battery is deeply discharged, removed, or contact-bounced (i.e., during a power cut), the RTC system and coin cell
maintained logic will switch over to the LICELL for backup power. This pin also works as a current-limited voltage source for
battery charging. A small capacitor should be placed from LICELL to ground under all circumstances.
XTAL1
32.768 kHz Oscillator crystal connection 1.
XTAL2
32.768 kHz Oscillator crystal connection 2.
GNDRTC
Ground for the RTC block.
CLK32K
32 kHz Clock output for peripherals. At system start-up, the 32 kHz clock is driven to CLK32K (provided as a peripheral clock
reference), which is referenced to SPIVCC. The CLK32K is restricted to state machine activation in normal on mode.
CLK32KMCU
32 kHz Clock output for processor. At system start-up, the 32 kHz clock is driven to CLK32KMCU (intended as the CKIL input
to the system processor) referenced to VSRTC. The driver is enabled by the start-up sequencer and the CLK32KMCU is
programmable for Low-power Off mode control by the state machine.
RESETB AND RESETBMCU
Reset output for peripherals and processor respectively. These depend on the Power Control Modes of operation ( See
Functional Device Operation on page 40 ). These are meant as reset for the processor, or peripherals in a power up condition, or
to keep one in reset while the other is up and running.
WDI
Watchdog input. This pin must be high to stay in the On mode. The WDI IO supply voltage is referenced to SPIVCC (normally
connected to SW4 = 1.8 V). SPIVCC must therefore remain enabled to allow for proper WDI detection. If WDI goes low, the
system will transition to the Off state or Cold Start (depending on the configuration).
STANDBY AND STANDBYSEC
Standby input signal from processor and from peripherals respectively.
To ensure that shared resources are properly powered when required, the system will only be allowed into Standby when both
the application processor (which typically controls the STANDBY pin) and peripherals (which typically control the STANDBYSEC
pin) allow it. This is referred to as a Standby event.
The Standby pins are programmable for Active High or Active Low polarity, and that decoding of a Standby event will take into
account the programmed input polarities associated with each pin. Since the Standby pin activity is driven asynchronously to the
system, a finite time is required for the internal logic to qualify and respond to the pin level changes.
The state of the Standby pins only have influence in the On mode and are therefore ignored during start up and in the
Watchdog phase. This allows the system to power up without concern of the required Standby polarities, since software can
make adjustments accordingly, as soon as it is running.
INT
Interrupt to processor. Unmasked interrupt events are signaled to the processor by driving the INT pin high.
MC13892
Analog Integrated Circuit Device Data
36
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| RCA18DTMD | CONN EDGECARD 36POS R/A .125 SLD |
| EVAL-ADG2108EBZ | BOARD EVAL FOR ADG2108 |
| RCA18DTBN | CONN EDGECARD 36POS R/A .125 SLD |
| RCA18DTBH | CONN EDGECARD 36POS R/A .125 SLD |
| GBM28DCMN | CONN EDGECARD 56POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC1-38RX | 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL |
| MC1391 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TV HORIZONTAL PROCESSOR |
| MC13917-1900EVK | 功能描述:射频开发工具 MC13917_1900_EVK RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MC13917-350EVK | 功能描述:射频开发工具 MC13917_350_EVK RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MC13917-434EVK | 功能描述:射频开发工具 MC13917 EVB 434MHZ RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。