收藏本站
参数资料
型号： MC13892VLR2
厂商： Freescale Semiconductor
文件页数： 62/158页
文件大小： 0K
描述： IC PMU I.MX51/37/35/27 186MAPBGA
标准包装： 1,000
应用： 电池管理，显示器（LED 驱动器），手持/移动设备，电源
工作温度： -40°C ~ 85°C
安装类型： 表面贴装
封装/外壳： 186-LFBGA
供应商设备封装： 186-PBGA（12x12）
包装： 带卷 (TR)
FUNCTIONAL DEVICE OPERATION
OPERATING MODES
Table 25. Timer Main Characteristics
Timer
Under-voltage Timer
Reset Timer
Watchdog Timer
Power Cut Timer
Duration
4.0 ms
40 ms
128 ms
Programmable 0 to 8 seconds in 31.25 ms steps
TIMING DIAGRAMS
A Turn On event timing diagram example shows in Figure 12 .
Figure 12. Power Up Timing Diagram
POWER UP
At power up, switchers and regulators are sequentially enabled in time slots of 2.0 ms steps to limit the inrush current after an
initial delay of 8.0 ms, in which the core circuitry gets enabled. To ensure a proper power up sequence, the outputs of the
switchers are discharged at the beginning of a Cold Start. For that reason, an 8.0 ms delay allows the outputs of the linear
regulators to be fully discharged as well through the built-in discharge path. Time slots which include multiple regulator startups
will be sub-sequenced for additional inrush balancing. The peak inrush current per event is limited. Any under-voltage detection
at BP is masked while the power up sequencer is running.
The Power Up mode Select pins (PUMS1 and 2) are used to configure the startup characteristics of the regulators. Supply
enabling and output level options are selected by hardwiring the PUMSx pins for the desired configuration. The state of the
PUMSx pins can be read out via the sense bits PUMSSxx[1:0]. Tying the PUMSx pins to ground corresponds to 00, open to 01,
VCOREDIG to 10, and VCORE to 11.
The recommended power up strategy for end products is to bring up as little of the system as possible at booting, essentially
sequestering just the bare essentials, to allow processor startup and software to run. With such a strategy, the startup transients
are controlled at lower levels, and the rest of the system power tree can be brought up by software. This allows optimization of
supply ordering where specific sequences may be required, as well as supply default values. Software code can load up all of
the required programmable options to avoid sneak paths, under/over-voltage issues, startup surges, etc., without any change in
hardware. For this reason, the Power Gate drivers are limited to activation by software rather than the sequencer, allowing the
core(s) to startup before any peripheral loading is introduced.
The power up defaults Table 26 shows the initial setup for the voltage level of the switchers and regulators, and whether they
get enabled.
MC13892
Analog Integrated Circuit Device Data
62
Freescale Semiconductor
相关PDF资料
PDF描述
RCA18DTMD CONN EDGECARD 36POS R/A .125 SLD
EVAL-ADG2108EBZ BOARD EVAL FOR ADG2108
RCA18DTBN CONN EDGECARD 36POS R/A .125 SLD
RCA18DTBH CONN EDGECARD 36POS R/A .125 SLD
GBM28DCMN CONN EDGECARD 56POS .156 WW
相关代理商/技术参数
参数描述
MC1-38RX 制造商:3M Electronic Products Division 功能描述:NON INSL COPPER SEAMLESS RING TE 制造商:3M Electronic Products Division 功能描述:80610253439 制造商:3M Electronic Products Division 功能描述:80610253439 MC1-38RX S/LOK RING TERMINAL
MC1391 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TV HORIZONTAL PROCESSOR
MC13917-1900EVK 功能描述:射频开发工具 MC13917_1900_EVK RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MC13917-350EVK 功能描述:射频开发工具 MC13917_350_EVK RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MC13917-434EVK 功能描述:射频开发工具 MC13917 EVB 434MHZ RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*