参数资料
| 型号： | MC33970DWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 10/36页 |
| 文件大小： | 0K |
| 描述： | IC GAUGE DRIVER SPI 24-SOIC |
| 标准包装： | 1 |
| 应用： | 步进电机驱动器，2 相 |
| 输出数： | 2 |
| 电流 - 输出： | 100mA |
| 电压 - 负载： | 6.5 V ~ 26 V |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
This 33970 is a single-packaged, Serial Peripheral
Interface (SPI) controlled, dual step motor gauge driver
integrated circuit (IC). This monolithic IC consists of four dual
output H-Bridge coil drivers and the associated control logic.
Each pair of H-Bridge drivers is used to automatically control
the speed, direction, and magnitude of current through the
The 33970 is ideal for use in automotive instrumentation
systems requiring distributed and flexible step motor gauge
driving. The device also eases the transition to step motors
from air core motors by emulating the air core pointer
movement with little additional processor bandwidth
utilization.
two coils of a two-phase instrumentation step motor, similar
to an MMT-licensed AFIC 6405.
FUNCTIONAL PIN DESCRIPTION
H-Bridge Outputs 0 (COS0+, COS0-, SIN0+, SIN0-)
Each pin is the output pin of a half bridge, designed to
source or sink current. The H-Bridge pins linearly drive the
sine and cosine coils of two separate step motors to provide
four-quadrant operation.
GROUND (GND)
These pins serve as the ground for the source of the low-
side output transistors as well as the logic portion of the
device. They also help dissipate heat from the device.
CHIP SELECT (CS)
The CS pin enables communication with the master
device. When this pin is in a logic [0] state, the 33970 is
capable of transferring information to, and receiving
information from, the master. The 33970 latches data in from
the Input Shift registers to the addressed registers on the
rising edge of CS . The output driver on the SO pin is enabled
when CS is logic [0]. When CS is logic high, signals at the
SCLK and SI pins ar e ignored and the SO pin is tri-stated
(high impedance). CS will only be transitioned from a logic [1]
state to a logic [0] state when SCLK is a logic [0]. CS has an
internal pull-up (l UP ) connected to the pin, as specified in the
section of the Static Electrical Characteristics table entitled
SERIAL OUTPUT (SO)
The SO data pin is a tri-stateable output from the Shift
register. The Status register bits are the first 16 bits shifted
out. Those bits are followed by the message bits clocked in
FIFO, when the device is in a daisy chain connection or being
sent words that are multiples of 16 bits. Data is shifted on the
rising edge of the SCLK signal. The SO pin will remain in a
high impedance state until the CS pin is put into a logic low
state.
SERIAL INPUT (SI)
The SI pin is the input of the Serial Peripheral Interface
(SPI). Serial Input (SI) information is read on the falling edge
of SCLK. A 16-bit stream of serial data is required on the SI
pin, beginning with the most significant bit (MSB). Messages
that are not multiples of 16 bits (e.g., daisy chained device
messages) are ignored. After transmitting a 16-bit word, the
CS pin must be de-asserted (logic [1]) before transmitting a
new word. SI information is ignored when CS is in a logic high
state.
Multiplexed Output (RTZ)
This is a multiplexed output pin, for the non-driven coil,
during a Return to Zero (RTZ) event.
CONTROL I/O , which is found on page 6 .
Voltage (VDD)
SERIAL CLOCK (SCLK)
SCLK clocks the Internal Shift registers of the 33970
device. The Serial Input (SI) pin accepts data into the Input
Shift register on the falling edge of the SCLK signal, while the
Serial Output pin (SO) shifts data information out of the SO
Line Driver on the rising edge of the SCLK signal. It is
important that the SCLK pin be in a logic [0] state whenever
the CS makes any transition. SCLK has an internal pull down
(l DWN ), as specified in the section of the Static Electrical
Characteristics table entitled CONTROL I/O , which is found
on page 6 . When CS is logic [1], signals at the SCLK and SI
pins are ignored and SO is tri-stated (high impedance). Refer
This SPI and logic power supply input will work with 5.0 V
supplies.
RESET (RST)
If the master decides to reset the device, or place it into a
sleep state, the RST pin is driven to a logic [0]. A logic [0] on
the RST pin will force all internal logic to the known default
state. This input has an internal active pull-up.
BATTERY VOLTAGE (VPWR)
Power supply.
to the data transfer timing diagrams in Figure 6 and Figure 7
33970
Analog Integrated Circuit Device Data
10
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MC33981BPNAR2 | IC SWITCH HI SIDE SINGLE 16-PQFN |
| MC33984BPNAR2 | IC SWITCH HI SIDE DUAL 16-PQFN |
| MC33988CPNA | IC SWITCH HIGH SIDE DUAL 16QFN |
| MC33997DW | IC SWITCH 3.3/5V SUPPLY 24-SOIC |
| MC34063AD | IC REG BUCK BOOST INV 1.5A 8SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33972ATEK | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972ATEKR2 | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972ATEW | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972ATEWR2 | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972DWB | 功能描述:IC SWITCH DETECT SPI 32-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
发布紧急采购，3分钟左右您将得到回复。