参数资料
| 型号： | MC33970DWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | IC GAUGE DRIVER SPI 24-SOIC |
| 标准包装： | 1 |
| 应用： | 步进电机驱动器，2 相 |
| 输出数： | 2 |
| 电流 - 输出： | 100mA |
| 电压 - 负载： | 6.5 V ~ 26 V |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Table 9. Gauge 0 Position Register (POS0R)
Address 010
Bits
Read
Write
D12
–
0
D11
–
P0 11
D10
–
P0 10
D9
–
P0 9
D8
–
P0 8
D7
–
P0 7
D6
–
P0 6
D5
–
P0 5
D4
–
P0 4
D3
–
P0 3
D2
–
P02
D1
–
P01
D0
–
P0 0
The bits in Table 9 are write-only .
P0 12 (D12) — This bit must be transmitted as logic [0] for
valid commands.
P0 11:P0 0 (D11:D0) — Desired pointer position of
Gauge 0. Pointer positions can range from 0
(000000000000) to position 4095 (111111111111). For a
step motor requiring 12 microsteps per degree of pointer
movement, the maximum pointer sweep is 341.25 °.
.
Table 10. Gauge 1 Position Register (POS1R)
Address 011
Bits
Read
Write
D12
–
0
D11
–
P1 11
D10
–
P1 10
D9
–
P1 9
D8
–
P1 8
D7
–
P1 7
D6
–
P1 6
D5
–
P1 5
D4
–
P1 4
D3
–
P1 3
D2
–
P1 2
D1
–
P1 1
D0
–
P1 0
The bits in Table 10 are write-only .
P1 12 (D12) — This bit must be transmitted as logic [0] for
valid commands.
P1 11:P1 0 (D11:D0) — Desired pointer position of
Gauge 1. Pointer positions can range from 0
(000000000000) to position 4095 (111111111111). For a
step motor requiring 12 microsteps per degree of pointer
movement, the maximum pointer sweep is 341.25 °
(4095 ÷ 12).
Address 100 — Gauge Return to Zero Register (RTZR)
is written to return the gauge pointers to the zero position.
During an RTZ event, the pointer is returned to zero using full
steps, where only one coil is driven at any point in time. The
driven coil is integrated and its results are stored in an
accumulator.
A logic [1] written to bit RZ1 enables a Return to Zero for
Gauge 0 if RZ0 is logic [0], and Gauge 1 if RZ0 is logic [1],
respectively. Similarly, a logic [0] written to bit RZ1 disables a
Return to Zero for Gauge 0 when RZ0 is logic [0], and
Gauge 1 when RZ0 is logic [1], respectively.
Bits D12:D5 and D3:D2 must be at logic [0] for valid RTZR
commands.
Bit RZ4 is used to enable an unconditional RTZ event. A
logic [0] results in a typical RTZ event, automatically
providing a Stop when a stall condition is detected. A logic [1]
will result in RTZ movement, causing a Stop if a logic [0] is
written to bit RZ0. This feature is useful during development
and characterization of RTZ requirements.
back electromotive force (EMF) signal present on the non-
Table 11. Return to Zero Register (RTZR)
Address 100
Bits
Read
Write
D12
–
0
D11
–
0
D10
–
0
D9
–
0
D8
–
0
D7
–
0
D6
–
0
D5
–
0
D4
–
RZ4
D3
–
0
D2
–
RZ2
D1
–
RZ1
D0
–
RZ0
The register bits in Table 11 are write-only .
RZ12:RZ5 (D12:D5) — These bits must be transmitted as
logic [0] for valid commands.
RZ4 (D4) — This bit is used to enable an unconditional
RTZ event.
? 0 = Automatic Return to Zero
? 1 = Unconditional Return to Zero
RZ3 (D3) — This bit must be transmitted as logic [0] for
valid commands.
RZ2 (D2) — Return to Zero Direction bit. This bit is used to
properly sequence the integrator, depending upon the
desired zeroing direction.
? 0 = Return to Zero will occur in the CCW direction
(PE7 = 0)
? 1 = Return to Zero will occur in the CW direction
(PE7 = 1)
33970
Analog Integrated Circuit Device Data
16
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MC33981BPNAR2 | IC SWITCH HI SIDE SINGLE 16-PQFN |
| MC33984BPNAR2 | IC SWITCH HI SIDE DUAL 16-PQFN |
| MC33988CPNA | IC SWITCH HIGH SIDE DUAL 16QFN |
| MC33997DW | IC SWITCH 3.3/5V SUPPLY 24-SOIC |
| MC34063AD | IC REG BUCK BOOST INV 1.5A 8SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC33972ATEK | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972ATEKR2 | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972ATEW | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972ATEWR2 | 功能描述:接口 - 专用 MULT SW DET SUP-WKUP RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MC33972DWB | 功能描述:IC SWITCH DETECT SPI 32-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 标准包装:3,000 系列:- 应用:PDA，便携式音频/视频，智能电话 接口:I²C，2 线串口 电源电压:1.65 V ~ 3.6 V 封装/外壳:24-WQFN 裸露焊盘 供应商设备封装:24-QFN 裸露焊盘（4x4） 包装:带卷 (TR) 安装类型:表面贴装 产品目录页面:1015 (CN2011-ZH PDF) 其它名称:296-25223-2 |
发布紧急采购，3分钟左右您将得到回复。