- 您现在的位置：买卖IC网 > PDF目录69027 > MC68HC05P9DWR2 (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | MC68HC05P9DWR2 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| 封装： | SOIC-28 |
| 文件页数： | 37/88页 |
| 文件大小： | 6557K |
| 代理商： | MC68HC05P9DWR2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
4
MOTOROLA
4-10
MC68HC05E0
RESETS, INTERRUPTS AND LOW POWER MODES
Note:
PITW (Program Interrupt Type Wake-up function), bit 4 of the Timer Control Register
($000C) provides additional control of wake-up interrupts on Port C by selecting either
edge or level sensitive triggering.
4.3
Low Power Modes
4.3.1
STOP
The STOP instruction places the MCU in its lowest power consumption mode. The processor can
only be started again by an external interrupt (on the INTX pin) (if enabled), a wake-up interrupt
(if enabled) or reset. The oscillator is stopped, all CPU and timer functions are stopped, and an
oscillator stabilisation delay of 4064 cycles is required to start the processor again.
Note:
The RTI Timer restarts immediately after exiting the STOP state.
During the STOP mode, the RTI interrupt ag and interrupt enable bits are cleared by internal
hardware to remove any pending interrupt requests. The RTI Timer prescaler is also cleared. The
I bit in the CCR is cleared to enable external interrupts or wake-up function interrupts. All other
bits and registers, and memory remain unaltered. All input/output lines remain unchanged.
Note:
Pending interrupts from Timer A, Timer B, and SI are not cleared by the stop instruction.
The external interrupt INTX can be disabled by the External Interrupt Mask bit (INTMX)
in the Interrupt Control Register ($000E).
4.3.2
WAIT
The WAIT instruction places the MCU in a low-power consumption mode, but the WAIT mode
consumes more power than the STOP mode. All CPU action is suspended, but the timers remain
active. An interrupt from the timer can cause the MCU to exit the WAIT mode. During the WAIT
mode, the I bit in the CCR is cleared to enable interrupts. All other registers, memory and
input/output lines remain in their previous state.
46
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC05RC18P | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
| MC68HC05RC18FN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05SR3FB | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC05SR3CFB | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC05T7B | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC05P9P | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05PV8 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Techinal Data - rev 1.9 |
| MC68HC05PV8A | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Techinal Data - rev 1.9 |
| MC68HC05RC16 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:General Release Specification |
| MC68HC05RC16DW | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:General Release Specification |
发布紧急采购，3分钟左右您将得到回复。