- 您现在的位置：买卖IC网 > PDF目录69027 > MC68HC05P9DWR2 (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | MC68HC05P9DWR2 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| 封装： | SOIC-28 |
| 文件页数： | 65/88页 |
| 文件大小： | 6557K |
| 代理商： | MC68HC05P9DWR2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页当前第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
8
MOTOROLA
8-8
MC68HC05E0
SERIAL INTERFACE
BD1, BD0 — Baud Rate Select Bits (see Table 8-2).
PS1, PS0 — Port Select Bits
These bits should be 01 (binary) to select an I2C-bus function (see Table 8-1).
The I2C-bus Interface is controlled via the SI S Register ($0011).
BB — Bus Busy Bit
BB is a read-only bit which indicates if the I2C-bus is busy or idle. BB is set if a START condition
is seen on the data line. This implies that another I2C-bus master is using the bus, and that if the
MC68HC05E0 tries to start an I2C-bus sequence a data/clock collision will occur. BB is cleared
when the corresponding STOP condition, implying that the bus is again idle, is detected on the
bus. This ag generates no interrupt.
1 (set)
–
Busy
0 (clear) –
Idle
ACK — Acknowledge Bit
ACK is a read-only bit which goes high if an acknowledge signal is given by a peripheral (via the
9th clock bit) after the MC68HC05E0 has transmitted a byte of data to it. ACK is updated at the
end of each receive sequence.
1 (set)
–
Acknowledgement received from peripheral
0 (clear) –
Acknowledgement not received from peripheral
TFF/DOIT — Transmission Failure Flag/“Do it” Bit
Writing this bit high starts an I2C-bus transaction. Reading this bit at the end of an I2C-bus
transmit sequence shows the state of the TFF ag. If high, this indicates a mismatch between data
in the SI Data Register and the data sent on the serial data line. Writing a zero to this bit clears
and resets the Transmission Failure Flag circuitry.
Read
Write
1 (set)
–
Transmission error
Start Send or Receive
0 (clear) –
No transmission error
Clear and reset TFF
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
Serial interface S register
$0011
BB
ACK
TFF/
DOIT
IRQ/
ACK
NMA
SP
ST
R/WB 0000 0000
74
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC05RC18P | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
| MC68HC05RC18FN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05SR3FB | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC05SR3CFB | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP44 |
| MC68HC05T7B | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HC05P9P | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05PV8 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Techinal Data - rev 1.9 |
| MC68HC05PV8A | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Techinal Data - rev 1.9 |
| MC68HC05RC16 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:General Release Specification |
| MC68HC05RC16DW | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:General Release Specification |
发布紧急采购，3分钟左右您将得到回复。