参数资料
型号: MC68HC11G5CFN
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: High-density Complementary Metal Oxide Semiconductor (HCMOS) Microcontroller
中文描述: 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC84
封装: PLASTIC, LCC-84
文件页数: 102/195页
文件大小: 839K
代理商: MC68HC11G5CFN
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页当前第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页
MOTOROLA
7-12
SERIAL COMMUNICATIONS INTERFACE
MC68HC11G5
NF — Noise Error Flag
This bit is set if there is noise on a “valid” start bit, any of the data bits, or on the stop bit.
The NF bit is set during the same cycle as the RDRF bit but does not get set in the case
of an overrun (OR).
FE — Framing Error Flag
This bit is set when the word boundaries in the bit stream are not synchronized with the
receiver bit counter (generated by the reception of a logic zero bit where a stop bit was
expected). The FE bit reflects the status of the byte in the receive data register and the
transfer from the receive shifter to the receive data register is inhibited in the case of
overrun. The FE bit is set during the same cycle as the RDRF bit but does not get set in
the case of an overrun (OR). The framing error flag inhibits further transfer of data into
the receive data register until it is cleared.
7.8.5
Baud Rate Register (BAUD)
The baud rate register (BAUD) is used to set the bit rate for the SCI system. Normally this register
is written once, during initialization, to set the baud rate for SCI communications. Both the receiver
and the transmitter use the same baud rate which is derived from the MCU bus rate clock. A two
stage divider is used to develop custom baud rates from normal MCU crystal frequencies so it is not
necessary to use special baud rate crystal frequencies.
TCLR
0
SCP1
SCP0
RCKB
SCR2
SCR1
SCR0
BAUD
$
1
02B
7
6
5
4
3
2
1
0
0
0
0
0
0
U
U
U
RESET:
TCLR — Clear Baud Rate Counters (for test purposes only)
READ:
Always returns 0.
WRITE:
Only while SMOD = 1 (test or bootstrap mode)
This bit is disabled and remains low in any mode other than test or bootstrap mode. Reset
clears this bit. While in test or bootstrap mode, setting this bit causes the baud rate
counter chains to be reset. The logic one state of this bit is transitory and reads always
return a logic zero. This control bit is intended only for factory testing of the MCU.
SCP1, SCP0 — Serial Prescaler Select bits
READ:
Any time
WRITE:
Any time
The E-clock is divided by the factors shown in Table 7-1. This prescaled output provides
an input to a divider which is controlled by the SCI rate select bits (SCR2 – SCR0).
相关PDF资料
PDF描述
MC68HLC908LJ12 Addendum to MC68HC908LJ12
MC68HLC908QT1 Microcontrollers
MC68HLC908QT2 Microcontrollers
MC68HLC908QT4 Microcontrollers
MC68HLC908QY1 Microcontrollers
相关代理商/技术参数
参数描述
MC68HC11G7 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:High-density Complementary Metal Oxide Semiconductor (HCMOS) Microcontroller Unit
MC68HC11G7CFN 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller
MC68HC11K0 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:HCMOS Microcontroller Unit
MC68HC11K0CFN2 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:8-Bit Microcontroller
MC68HC11K0CFN3 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:8-Bit Microcontroller