- 您现在的位置：买卖IC网 > PDF目录8855 > MCP4726A1T-E/MAY (Microchip Technology)IC DAC 12BIT NV EEP I2C 6DFN PDF资料下载
参数资料
| 型号： | MCP4726A1T-E/MAY |
| 厂商： | Microchip Technology |
| 文件页数： | 30/86页 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT NV EEP I2C 6DFN |
| 标准包装： | 3,000 |
| 设置时间： | 6µs |
| 位数： | 12 |
| 数据接口： | EEPROM，I²C，串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 1.10W |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-VDFN 裸露焊盘 |
| 供应商设备封装： | 6-DFN（2x2） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 1 电压，单极 |
| 采样率（每秒）： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页
MCP4706/4716/4726
DS22272C-page 36
2011-2012 Microchip Technology Inc.
4.2
DAC’s (Resistor Ladder)
Reference Voltage
The device can be configured to use one of three
voltage sources for the resistor ladder’s reference
1.
VDD pin voltage
2.
VREF pin voltage internally buffered
3.
VREF pin voltage unbuffered
The selection of the voltage is specified with the volatile
are nonvolatile and volatile VREF1:VREF0 Configuration
bits. On a POR/BOR event, the state of the nonvolatile
VREF1:VREF0 Configuration bits are latched into the
volatile VREF1:VREF0 Configuration bits.
When the user selects the VDD as reference, the VREF
pin voltage is not connected to the resistor ladder.
If the VREF pin is selected, then select between the
Buffered or Unbuffered mode.
In Unbuffered mode, the VREF pin voltage may be from
VSS to VDD.
In Buffered mode, the VREF pin voltage may be from
0.01V to VDD-0.04V. The input buffer (amplifier) pro-
vides low offset voltage, low noise, and a very high
input impedance, with only minor limitations on the
input range and frequency response.
FIGURE 4-2:
Resistor Ladder Reference
Voltage Selection Block Diagram.
4.3
Resistor Ladder
The resistor ladder is a digital potentiometer with the B
Terminal internally grounded and the A terminal
connected to the selected reference voltage (see
Figure 4-3). The volatile DAC register controls the
wiper position. The wiper voltage (VW) is proportional to
the DAC register value divided by the number of
resistor elements (RS) in the ladder (256, 1024, or
4096) related to the VRL voltage.
The resistor ladder (RRL) has a typical impedance of
approximately 210 k
Ω. This resistor ladder resistance
(RRL) may vary from device to device up to ±20%.
Since this is a voltage divider configuration, the actual
RRL resistance does not effect the output given a fixed
voltage at VRL.
If the unbuffered VREF pin is used as the VRL voltage
source, this voltage source should have a low output
impedance.
When the DAC is powered down, the resistor ladder is
disconnected from the selected reference voltage.
FIGURE 4-3:
Resistor Ladder.
Note:
In Unbuffered mode, the voltage source
should have a low output impedance. If
the voltage source has a high output
impedance, then the voltage on the
VREF’s pin would be lower than expected.
The
resistor
ladder
has
a
typical
impedance of 210 k
Ω and a typical
capacitance of 29 pF.
Note:
Any variation or noises on the reference
source can directly affect the DAC output.
The reference voltage needs to be as
clean as possible for accurate DAC
performance.
VRL
VDD
Buffer
R
e
fere
nc
e
VREF1:VREF0
Se
le
c
ti
o
n
VREF
Note:
The maximum wiper position is 2n - 1,
while the number of resistors in the
resistor ladder is 2n. This means that
when the DAC register is at full scale,
there
is
one
resistor
element
(RS)
between the wiper and the VRL voltage.
RS(2n)
RS(2n - 1)
RS(2n - 2)
RS(1)
2n - 1
2n - 2
1
0
RRL
VRL
VW
DAC
Register
VW =
* VRL
DAC Register Value
# Resistors in Resistor Ladder
Where:
# Resistors in Resistor Ladder = 256 (MCP4706)
1024 (MCP4716)
4096 (MCP4726)
PD1:PD0
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/84G2219N | CONN RCPT 19POS JAM NUT W/SCKT |
| V28B36M150B3 | CONVERTER MOD DC/DC 36V 150W |
| ICS570BI | IC MULTIPLIER/ZDB 8-SOIC |
| MCP4726A1T-E/CH | IC DAC 12BIT NV EEP I2C SOT-23-6 |
| MS3454L22-21S | CONN RCPT 3POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4726A2T-E/CH | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A2T-E/MAY | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A3T-E/CH | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A3T-E/MAY | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4728A0-E/UN | 功能描述:数模转换器- DAC Quad, 12-bit NV DAC with I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。