- 您现在的位置：买卖IC网 > PDF目录8855 > MCP4726A1T-E/MAY (Microchip Technology)IC DAC 12BIT NV EEP I2C 6DFN PDF资料下载
参数资料
| 型号： | MCP4726A1T-E/MAY |
| 厂商： | Microchip Technology |
| 文件页数： | 35/86页 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT NV EEP I2C 6DFN |
| 标准包装： | 3,000 |
| 设置时间： | 6µs |
| 位数： | 12 |
| 数据接口： | EEPROM，I²C，串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 1.10W |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-VDFN 裸露焊盘 |
| 供应商设备封装： | 6-DFN（2x2） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 1 电压，单极 |
| 采样率（每秒）： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页
MCP4706/4716/4726
DS22272C-page 40
2011-2012 Microchip Technology Inc.
4.5
Power-Down Operation
To allow the application to conserve power when the
DAC operation is not required, three Power-Down
modes are available. The Power-Down Configuration
bits (PD1:PD0) control the power-down operation
(Figure 4-7). All Power-Down modes do the following:
Turn off most of its internal circuits (op amp, resis-
tor ladder, ...)
Op amp output becomes high-impedance to the
VOUT pin
Disconnects resistor ladder from reference
voltage (VRL)
Retains the value of the volatile DAC register and
Configuration bits, and the nonvolatile (EEPROM)
DAC register and Configuration bits
Depending on the selected Power-Down mode, the
following will occur:
VOUT pin is switched to one of three resistive pull-
downs (See Table 4-2)
- 640k
Ω (typical)
- 125k
Ω (typical)
-1k
Ω (typical)
There is a delay (TPDE) between the PD1:PD0 bits
changing from ‘00’ to either ‘01’, ‘10’, or ‘11’ and the op
amp no longer driving the VOUT output and the pull-
down resistors are sinking current.
In any of the Power-Down modes, where the VOUT pin
is not externally connected (sinking or sourcing
current), the power-down current will typically be 60 nA
Section 6.0 “MCP47X6 I2C Commands” describes
the I2C commands for writing the power-down bits. The
commands that can update the volatile PD1:PD0 bits
are:
FIGURE 4-7:
Op Amp to VOUT Pin Block
Diagram.
4.5.1
EXITING POWER-DOWN
When the device exits the Power-Down mode, the
following occurs:
Disabled circuits (op amp, resistor ladder, ...) are
turned on
Resistor ladder is connected to selected
reference voltage (VRL)
Selected pull-down resistor is disconnected
The VOUT output will be driven to the voltage
represented by the volatile DAC register’s value
and Configuration bits
The VOUT output signal will require time as these
circuits are powered up and the output voltage is driven
to the specified value as determined by the volatile
DAC register and Configuration bits.
The following events will change the PD1:PD0 bits to
‘00’ and therefore exit the Power-Down mode. These
are:
Any I2C Write command for where the PD1:PD0
bits are ‘00’
(if nonvolatile PD1:PD0 bits are ‘00’)
Note:
The I2C serial interface circuit is not
affected by the Power-Down mode. This
circuit remains active in order to receive
any command that might come from the
I2C master device.
TABLE 4-2:
POWER-DOWN BITS AND
OUTPUT RESISTIVE LOAD
PD1
PD0
Function
00
Normal operation
01
1k
Ω resistor to ground
10
125 k
Ω resistor to ground
11
640 k
Ω resistor to ground
Note:
Since the op amp and resistor ladder were
powered off (0V), the op amp’s input
voltage (VW) can be considered 0V. There
is a delay (TPDD) between the PD1:PD0
bits updated to ‘00’ and the op amp driving
the VOUT output. The op amp’s settling
time (from 0V) needs to be taken into
account to ensure the VOUT voltage
reflects the selected value.
VOUT
PD1:PD0
Op
Amp
1k
Ω
125
k
Ω
64
0
k
Ω
Gain (1x or 2x)
(Gx = 0 or 1)
VW
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/84G2219N | CONN RCPT 19POS JAM NUT W/SCKT |
| V28B36M150B3 | CONVERTER MOD DC/DC 36V 150W |
| ICS570BI | IC MULTIPLIER/ZDB 8-SOIC |
| MCP4726A1T-E/CH | IC DAC 12BIT NV EEP I2C SOT-23-6 |
| MS3454L22-21S | CONN RCPT 3POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4726A2T-E/CH | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A2T-E/MAY | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A3T-E/CH | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A3T-E/MAY | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4728A0-E/UN | 功能描述:数模转换器- DAC Quad, 12-bit NV DAC with I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。