- 您现在的位置：买卖IC网 > PDF目录8855 > MCP4726A1T-E/MAY (Microchip Technology)IC DAC 12BIT NV EEP I2C 6DFN PDF资料下载
参数资料
| 型号： | MCP4726A1T-E/MAY |
| 厂商： | Microchip Technology |
| 文件页数： | 31/86页 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT NV EEP I2C 6DFN |
| 标准包装： | 3,000 |
| 设置时间： | 6µs |
| 位数： | 12 |
| 数据接口： | EEPROM，I²C，串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 1.10W |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-VDFN 裸露焊盘 |
| 供应商设备封装： | 6-DFN（2x2） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 1 电压，单极 |
| 采样率（每秒）： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页
2011-2012 Microchip Technology Inc.
DS22272C-page 37
MCP4706/4716/4726
4.4
Output Buffer/VOUT Operation
The DAC output is buffered with a low power and
precision output amplifier (op amp). Figure 4-4 shows
a block diagram.
This amplifier provides a rail-to-rail output with low
offset voltage and low noise. The user can select the
output gain of the output amplifier. Gain options are:
a)
Gain of 1, with either VDD or VREF pin used as
reference voltage
b)
Gain of 2, only when VREF pin is used as
reference voltage. The VREF pin voltage should
be limited to VDD/2.
The amplifier’s output can drive the resistive and high
capacitive loads without oscillation. The amplifier
provides a maximum load current which is enough for
most programmable voltage reference applications.
Refer to Section 1.0 “Electrical Characteristics” for
the specifications of the output amplifier.
In any of the three Power-Down modes, the op amp is
powered down and its output becomes a high-
impedance to the VOUT pin.
FIGURE 4-4:
Output Buffer Block
Diagram.
4.4.1
PROGRAMMABLE GAIN
The amplifier’s gain is controlled by the Gain (G)
selection. When the VRL reference selection is the
device’s VDD voltage, the G bit is ignored and a gain of
1 is used. The volatile G bit value can be modified by:
POR event
BOR event
I2C Write commands
I2C General Call Reset command
4.4.2
OUTPUT VOLTAGE
The volatile DAC register’s value controls the analog
VOUT voltage, along with the device’s five Configuration
bits. The volatile DAC register’s value is unsigned
binary.
The formula for the output voltage is given in
Equation 4-1. Table 4-1 shows examples of volatile
DAC register values and the corresponding theoretical
VOUT voltage for the MCP47X6 devices.
EQUATION 4-1:
CALCULATING OUTPUT
VOLTAGE (VOUT)
The DAC register value will be latched on the falling
edge
of
the
Acknowledge
pulse
of
the
Write
command’s last byte. Then the VOUT voltage will start
driving to the new value.
The following events update the analog voltage output
(VOUT):
Power-on Reset or General Call Reset command:
Output is updated with EEPROM data.
Falling edge of the Acknowledge pulse of the last
Write command byte.
4.4.2.1
Resolution/Step Voltage
The Step voltage is dependent on the device resolution
and the output voltage range. One LSb is defined as
the ideal voltage difference between two successive
codes. The step voltage can easily be calculated by
using Equation 4-1 where the DAC register value is
equal to 1.
Note:
The load resistance must stay higher than
5k
Ω for the stable and expected analog
output to meet electrical specifications.
VOUT
Op
Amp
Gain (1x or 2x)
(G = 0 or 1)
VW
Note:
When Gain = 2 (VRL = VREF),
if VREF > VDD/2, the VOUT voltage will be
limited to VDD. So if VREF = VDD, then the
VOUT voltage will not change for volatile
DAC
register
values
mid-scale
and
greater, since the op amp is at its full scale
output.
VOUT =
* Gain
VRL * DAC Register Value
# Resistors in Resistor Ladder
# Resistors in Resistor Ladder = 4096 (MCP4726)
1024 (MCP4716)
256 (MCP4706)
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/84G2219N | CONN RCPT 19POS JAM NUT W/SCKT |
| V28B36M150B3 | CONVERTER MOD DC/DC 36V 150W |
| ICS570BI | IC MULTIPLIER/ZDB 8-SOIC |
| MCP4726A1T-E/CH | IC DAC 12BIT NV EEP I2C SOT-23-6 |
| MS3454L22-21S | CONN RCPT 3POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4726A2T-E/CH | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A2T-E/MAY | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A3T-E/CH | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4726A3T-E/MAY | 功能描述:数模转换器- DAC Sngl 12B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4728A0-E/UN | 功能描述:数模转换器- DAC Quad, 12-bit NV DAC with I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。