参数资料
| 型号： | MIC3001BML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 15/76页 |
| 文件大小： | 0K |
| 描述： | IC FOM MANAGEMENT W/CALIBR 24MLF |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 规程： | SDHj Sonet |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 供应商设备封装： | 24-MLF?（4x4） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC3001BMLTR MIC3001BMLTR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Micrel, Inc.
MIC3001
August 2004
22
M9999-082404-A
hbwhelp@micrel.com or (408) 955-1690
C/ ADC Result Registers Reading
In the present revision of MIC3001, the ADC result
registers should be read as 16 bit registers under internal
calibration while under external calibration they should be
read as 8 bit registers at the MSB address. For example,
TX power should be read under internal calibration as 16
bits at address A2h: 66–67 and under external calibration
as 8 bits at address A2h: 66h.
RXPOT
A
programmable,
non-volatile
digitally
controlled
potentiometer is provided for adjusting the gain of the
receive power measurement signal chain in the analog
domain. Five bits in the RXPOT register are used to set
and adjust the position of potentiometer. RXPOT
functions as a programmable divider or attenuator. It is
adjustable in steps from 1:1 (no divider action) down to
1/32 in steps of 1/32. If RXPOT is set to zero, the divider
is bypassed completely. There will be no scaling of the
input signal, and the resistor network will be disconnected
from the VRX pin. At all other settings of RXPOT, there
will be a 32k
(typical) load seen on VRX.
Figure 3. RXPOT Block Diagram
Laser Diode Bias Control
The MIC3001 can be configured to generate a constant
bias current using electrical feedback, or regulate average
transmitted optical power using a feedback signal from a
monitor photodiode, see Figure 4. An operational
amplifier is used to control laser bias current via the VBIAS
output. The VBIAS pin can drive a maximum of ±10mA.
An external bipolar transistor provides current gain. The
polarity of the op amp’s output is programmable
BIASREF in OEMCFG1 in order to accommodate either
NPN or PNP transistors that drive common anode and
common cathode laser, respectively. Additionally, the
polarity of the feedback signal is programmable for use
with either common-emitter or emitter-follower transistor
circuits.
Furthermore, the reference level for the APC circuit is
selectable to accommodate electrical, i.e., current feedback,
or optical feedback via a monitor photodiode. Finally, any
one of seven different internal feedback resistors can be
selected. This internal resistor can be used alone or in
parallel with an external resistor. This wide range of
adjustability (50:1)
accommodates
a
wide
range
of
photodiode current, i.e, wide range of transmitter output
power. The APC operating point can be kept near the mid-
scale value of the APC DAC, insuring maximum SNR,
maximum effective resolution for digital diagnostics, and the
widest possible DAC adjustment range for temperature
compensation, etc. See Figure 5.
The APCCAL bit in OEMCAL0 is used to turn the APC
function on and off. It will be turned off in the MIC3001’s
default state as shipped from the factory. When APC is on,
the value in the selected APCSETx register is added to the
signed value taken from the APC look-up table and loaded
into the VBIAS DAC. When APC is off, the VBIAS DAC may
be written directly via the VBIAS register, bypassing the look-
up table entirely. This provides direct control of the laser
diode bias during setup and calibration. In either case, the
VBIAS DAC setting is reported in the APCDAC register. The
APCCFG bits determine the DACs response to higher or
lower numeric values.
Figure 4. MIC3001 APC and Modulation Control
Block Diagram
Figure 5. Programmable Feedback Resistor
相关PDF资料 |
PDF描述 |
|---|---|
| MIC74BQS TR | IC I/O EXPANDER I2C 8B 16QSOP |
| MICRF302YML TR | IC ENCODER PAR QWIKRADIO 10-MLF |
| MK10DN512ZVLL10 | IC ARM CORTEX MCU 512KB 100LQFP |
| MK10DX128VFM5 | IC ARM CORTEX MCU 128KB 32QFN |
| MK20DN512ZVLL10 | IC ARM CORTEX MCU 512KB 100LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3001GML | 功能描述:网络控制器与处理器 IC F/O Transceiver Mgt. IC with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3001GML TR | 功能描述:网络控制器与处理器 IC F/O Transceiver Mgt. IC with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3001GMLTR | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC3002 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibr ation |
| MIC3002_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
发布紧急采购，3分钟左右您将得到回复。