参数资料
| 型号： | MIC3001BML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 50/76页 |
| 文件大小： | 0K |
| 描述： | IC FOM MANAGEMENT W/CALIBR 24MLF |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 规程： | SDHj Sonet |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 供应商设备封装： | 24-MLF?（4x4） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC3001BMLTR MIC3001BMLTR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Micrel, Inc.
MIC3001
August 2004
54
M9999-082404-A
hbwhelp@micrel.com or (408) 955-1690
OEM Password Entry (OEMPW)
D[7]
read/write
D[6]
read/write
D[5]
read/write
D[4]
read/write
D[3]
read/write
D[2]
read/write
D[1]
read/write
D[0]
read/write
Default Value
0000 0000b = 00h (reset to zero at power-on)
Serial Address
A2h = 1010001b
Byte Address
120 – 123 = 78h - 7Bh
(MSB is 7Bh)
This four-byte field is for entry of the password required to access the OEM area of the MIC3001’s memory and registers. A
valid OEM password will also permit access to the user areas of memory. The byte at address 123 (7Bh) is the most significant
byte. This field is compared to the four-byte OEMPWSET field at serial address A6h, bytes 12 to 15. If the two fields match,
access is allowed to the OEM areas of the MIC3001 non-volatile memory at serial addresses A4h and A6h. The OEM password
is set by writing the new value into OEMPWSET. The password comparison is performed following the write to the MSB,
address 7Bh. This byte must be written last!
A four-byte burst-write sequence to address 78h may be used as this will result in the MSB being written last. The new
password will not take effect until after a power-on reset occurs or a warm reset is performed using the RST bit in OEMCFG0.
This allows the new password to be verified before it takes effect. This field is reset to all zeros at power on. Any values written
to these locations will be readable by the host regardless of the locked/unlocked status of the device. If OEMPWSET is set to
zero (00000000h), the MIC3001 will remain unlocked regardless of the contents of the OEMPW field. This is the factory default
security setting.
Byte
Weight
3
OEM Password Entry, Most Significant Byte (Address = 7Bh)
2
OEM Password Entry, 2nd Most Significant Byte (Address = 7Ah)
1
OEM Password Entry, 2nd Least Significant Byte (Address = 79h)
0
OEM Password Entry, Least Significant Byte (Address = 78h)
USER Password Setting (USRPWSET)
D[7]
read/write
D[6]
read/write
D[5]
read/write
D[4]
read/write
D[3]
read/write
D[2]
read/write
D[1]
read/write
D[0]
read/write
Default Value
0000 0000b = 00h
Serial Address
A2h = 1010001b
Byte Address
250 = FAh
This register is for setting the password required to access the USER area of the MIC3001’s memory and registers. This field is
compared to the USRPW field at serial address A2h, byte 251. If the two fields match, access is allowed to the USER areas of
the MIC3001 non-volatile memory at serial addresses A0h and A2h. If a valid USER password has not been entered, writes to
the serial ID fields, USRCTRL, and the user scratchpad areas of A0h and A2h will not be allowed, and USRPWSET will be
unreadable (returns all zeroes).
A USER password is set by writing the new value into USRPWSET. The new password will not take effect until after a power-on
reset occurs or a warm reset is performed using the RST bit in OEMCFG0. This allows the new password to be verified before it
takes effect. This register is non-volatile and will be maintained through power and reset cycles. A valid USER or OEM
password is required for access to this register. Otherwise, this register will read as 00h. Note: a valid OEM password overrides
the USER password setting. If a valid OEM password is currently in place, the user password will have no effect.
相关PDF资料 |
PDF描述 |
|---|---|
| MIC74BQS TR | IC I/O EXPANDER I2C 8B 16QSOP |
| MICRF302YML TR | IC ENCODER PAR QWIKRADIO 10-MLF |
| MK10DN512ZVLL10 | IC ARM CORTEX MCU 512KB 100LQFP |
| MK10DX128VFM5 | IC ARM CORTEX MCU 128KB 32QFN |
| MK20DN512ZVLL10 | IC ARM CORTEX MCU 512KB 100LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3001GML | 功能描述:网络控制器与处理器 IC F/O Transceiver Mgt. IC with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3001GML TR | 功能描述:网络控制器与处理器 IC F/O Transceiver Mgt. IC with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3001GMLTR | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC3002 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibr ation |
| MIC3002_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
发布紧急采购，3分钟左右您将得到回复。