参数资料
| 型号： | MIC3001BML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 31/76页 |
| 文件大小： | 0K |
| 描述： | IC FOM MANAGEMENT W/CALIBR 24MLF |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 规程： | SDHj Sonet |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 供应商设备封装： | 24-MLF?（4x4） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC3001BMLTR MIC3001BMLTR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Micrel, Inc.
MIC3001
August 2004
37
M9999-082404-A
hbwhelp@micrel.com or (408) 955-1690
Figure 25. Four-Byte Page_White Protocol
Acknowledge Polling
The MIC3001’s non-volatile memory cannot be accessed
during the internal write process. To allow for maximum
speed bulk writes, the MIC3001 supports acknowledge
polling. The MIC3001 will not acknowledge serial bus
transactions while internal writes are in progress. The
host may therefore monitor for the end of the write
process
by
periodically
checking
for
an
acknowledgement.
Write Protection and Data Security
OEM Password
A password is required to access the OEM areas of the
MIC3001, specifically the non-volatile memory, look-up
tables, and registers at serial addresses A4h and A6h. A
four-byte field, OEMPWSET, at serial address A6h is
used for setting the OEM password. The OEM password
is set by writing OEMPWSET with the new value. The
password comparison is performed following the write to
the MSB of the OEMPW, address 7Bh at serial address
A2h. Therefore, this byte must be written last! A four-
byte burst-write sequence to address 78h may be used as
this will result in the MSB being written last. The new
password will not take effect until after a power-on reset
occurs or a warm reset is performed using the RST bit in
OEMCFG0. This allows the new password to be verified
before it takes effect.
The corresponding four-byte field for password entry,
OEMPW, is located at serial address A2h. This field is
therefore always visible to the host system. OEMPW is
compared to the four-byte OEMPWSET field at serial
address A6h. If the two fields match, access is allowed to
the OEM areas of the MIC3001 non-volatile memory at
serial addresses A4h and A6h. If OEMPWSET is all
zeroes, no password security will exist. The value in
OEMPW will be ignored. This helps prevent a deliberately
unsecured MIC3001 from being inadvertently locked.
Once a valid password is entered, the MIC3001 OEM
areas will be accessible. The OEM areas may be re-
secured by writing an incorrect password value at OEMPW,
e.g., all zeroes. In all cases OEMPW must be written LSB
first through MSB last. The OEM areas will be inaccessible
following the final write operation to OEMPW’s LSB. The
OEMPW field is reset to all zeros at power on. Any values
written to these locations will be readable by the host
regardless of the locked/unlocked status of the device. If
OEMPWSET is set to zero (00000000h), the MIC3001 will
remain unlocked regardless of the contents of the OEMPW
field. This is the factory default security setting.
NOTE: A valid OEM password allows access to the OEM
and user areas of the chip, i.e., the entire memory map,
regardless of any user password that may be in place. Once
the OEM areas are locked, the user password can provide
access and write protection for the user areas.
User Password
A password is required to access the USER areas of the
MIC3001, specifically the non-volatile memory at serial
addresses A0h and A2h. A one-byte field, USRPWSET at
serial address A2h is used for setting the USER password.
USRPWSET is compared to the USRPW field at serial
address A2h. If the two fields match, access is allowed to
the USER areas of the MIC3001 non-volatile memory at
serial addresses A0h and A2h. The USER password is set
by writing USRPWSET with the new value. The new
password will not take effect until after a power-on reset
occurs or a warm reset is performed using the RST bit in
OEMCFG0. This allows the new password to be verified
before it takes effect.
NOTE: A valid OEM password allows access to the OEM
and user areas of the chip, i.e., the entire memory map,
regardless of any user password that may be in place. Once
the OEM areas are locked, the user password can provide
access and write protection for the user areas. If a valid
OEM password is in place, the user password will have no
effect.
相关PDF资料 |
PDF描述 |
|---|---|
| MIC74BQS TR | IC I/O EXPANDER I2C 8B 16QSOP |
| MICRF302YML TR | IC ENCODER PAR QWIKRADIO 10-MLF |
| MK10DN512ZVLL10 | IC ARM CORTEX MCU 512KB 100LQFP |
| MK10DX128VFM5 | IC ARM CORTEX MCU 128KB 32QFN |
| MK20DN512ZVLL10 | IC ARM CORTEX MCU 512KB 100LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3001GML | 功能描述:网络控制器与处理器 IC F/O Transceiver Mgt. IC with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3001GML TR | 功能描述:网络控制器与处理器 IC F/O Transceiver Mgt. IC with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3001GMLTR | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC3002 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibr ation |
| MIC3002_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
发布紧急采购，3分钟左右您将得到回复。