参数资料
型号: MM908E621ACDWBR2
厂商: Freescale Semiconductor
文件页数: 17/60页
文件大小: 0K
描述: IC SW QUAD HB/TRPL HISID 54-SOIC
标准包装: 1,000
应用: 自动镜像控制
核心处理器: HC08
程序存储器类型: 闪存(16 kB)
控制器系列: 908E
RAM 容量: 512 x 8
接口: SCI,SPI
输入/输出数: 12
电源电压: 9 V ~ 16 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 54-BSSOP(0.295",7.50mm 宽)裸露焊盘
包装: 带卷 (TR)
供应商设备封装: 54-SOICW-EP
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
908E621
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
908E621 ANALOG DIE MODES OF OPERATION
The 908E621 offers three operating modes: Normal (Run),
Stop, and Sleep. In Normal mode, the device is active and is
operating under normal application conditions. The Stop and
Sleep modes are low power modes with wake-up capabilities.
The different modes can be selected by the STOP and
SLEEP bits in the System Control Register.
Figure 11 describes how transitions are done between the
different operating modes and Table 6, page 26, gives an
overview of the operating modes.
Figure 11. Operating Modes and Transitions
Normal Mode
This Mode is the normal operating mode of the device, all
functions and power stages are active and can be enabled/
disabled. The voltage regulator provides the +5.0 V VDD to
the MCU.
After a reset (e.g. Power-On-Reset, Wake-up from Sleep),
the MCU has to set the PSON bit in the System Control
Register within 80 ms typical (tNORMREQ). This is to ensure
the MCU has started up and is operating correctly. If the
PSON bit is not set within the required time frame, the device
enters SLEEP mode to reduce power consumption (fail safe).
This MCU monitoring can be disabled (e.g. for
programming) by applying VDD on the TESTMODE pin.
Stop Mode
In Stop mode, the voltage regulator still supplies the MCU
with VDD (limited current capability). To enter the Stop mode,
the STOP bit in the System Control Register must be set, and
the MCU has to be stopped also (see 908EY16 datasheet for
details).
Wake-up from this mode is possible by the LIN bus activity
or the wake-up input L0. It is maskable with the LINIE and/or
L0IE bits in the Interrupt Mask Register. The analog die is
generating an interrupt on IRQ_A pin to wake-up the MCU.
The wake-up / interrupt source can be evaluated with the
L0IF and LINIF bits in the Interrupt Flag Register.
Stop mode has a higher current consumption than Sleep
mode, but allows a quicker wake-up. Additionally the wake-
RESET
Power
Down
Power Up
Normal
Request
VDD High and Reset Delay (tRST) expired
NORMAL
SLEEP
Wake-up (Reset)
STOP
Reset (LVR, ext. Reset, (HTR))
SLEEP Command
S
T
O
P
C
om
m
and
Wake-Up
Interr
upt
PSON
=
1
VDD Low
Reset (LVR, HTR, WDR, ext. Reset)
Reset (LVR, ext. Reset)
TE
ST
MODE
=
1
PSON = 0 and Normal Request
timeout (tNORMREQ) expired
相关PDF资料
PDF描述
MM908E622ACEK IC HALF-BRIDGE QUAD 54-SOIC
MM908E624ACEWR2 IC SWITCH TRPL HI MCU/LIN 54SOIC
MM908E625ACDWB IC QUAD HALF BRDG MCU/LIN 54SOIC
MM908E626AVDWB IC STEPPER MOTOR DRIVER 54-SOIC
MM912F634BV1AER2 IC MCU 16BIT 32KB FLASH 48LQFP
相关代理商/技术参数
参数描述
MM908E621ACPEK 功能描述:8位微控制器 -MCU QUAD H-B/3-HS W/MCU & LI RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MM908E621ACPEKR2 功能描述:8位微控制器 -MCU QUAD HB AND TRIPLE HS RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MM908E622 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-Bridge, Triple High-Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror
MM908E622_08 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-bridge, Triple High Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror
MM908E622ACDR2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Quad Half-Bridge, Triple High-Side and EC Glass Driver with Embedded MCU and LIN for High End Mirror