- 您现在的位置：买卖IC网 > PDF目录3914 > MM908E625ACEK (Freescale Semiconductor)IC HALF-BRIDGE QUAD 54-SOIC PDF资料下载
参数资料
| 型号： | MM908E625ACEK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/49页 |
| 文件大小： | 0K |
| 描述： | IC HALF-BRIDGE QUAD 54-SOIC |
| 标准包装： | 26 |
| 应用： | 自动镜像控制 |
| 核心处理器： | HC08 |
| 程序存储器类型： | 闪存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 输入/输出数： | 13 |
| 电源电压： | 8 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 54-SOICW-EP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Analog Integrated Circuit Device Data
24
Freescale Semiconductor
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
ANALOG DIE I/OS
LIN Physical Layer
The LIN bus pin provides a physical layer for single-wire
communication in automotive applications. The LIN physical
layer is designed to meet the LIN physical layer specification.
The LIN driver is a low side MOSFET with internal current
limitation and thermal shutdown. An internal pull-up resistor
with a serial diode structure is integrated, so no external pull-
up components are required for the application in a slave
node. The fall time from dominant to recessive and the rise
time from recessive to dominant is controlled. The symmetry
between both slew rate controls is guaranteed.
The LIN pin offers high susceptibility immunity level from
external disturbance, guaranteeing communication during
external disturbance.
The LIN transmitter circuitry is enabled by setting the
PSON bit in the System Control Register (SYSCTL). If the
transmitter works in the current limitation region, the LINCL
bit in the System Status Register (SYSSTAT) is set. Due to
excessive power dissipation in the transmitter, software is
advised to monitor this bit and turn the transmitter off
immediately.
TXD PIN
The TXD pin is the MCU interface to control the state of the
LIN transmitter (see Figure 1). When TXD is LOW, LIN output
is low (dominant state). When TXD is HIGH, the LIN output
MOSFET is turned off. The TXD pin has an internal pull-up
current source in order to set the LIN bus in recessive state
in the event, for instance, the microcontroller could not control
it during system power-up or power-down.
RXD PIN
The RXD transceiver pin is the MCU interface, which
reports the state of the LIN bus voltage. LIN HIGH (recessive
state) is reported by a high level on RXD, LIN LOW (dominant
state) by a low level on RXD.
STOP MODE/WAKE-UP FEATURE
During STOP mode operation the transmitter of the
physical layer is disabled. The receiver pin is still active and
able to detect wake-up events on the LIN bus line.
If LIN interrupt is enabled (LINIE bit in the Interrupt Mask
Register is set), a falling edge on the LIN line causes an
interrupt. This interrupt switches on the main voltage
regulator and generates a system wake-up.
Analog Multiplexer/ADOUT Pin
The ADOUT pin is the analog output interface to the ADC
of the MCU. See Figure 12. An analog multiplexer is used to
read seven internal diagnostic analog voltages.
Current Recopy
The analog multiplexer is connected to the four low side
current sense circuits of the half-bridges. These sense
circuits offer a voltage proportional to the current through the
low side MOSFET. High or low resolution is selectable: 5.0 V/
2.5 A or 5.0 V/500 mA, respectively. Refer to Half-Bridge
Analog Input PA1
The analog input PA1 is directly connected to the analog
multiplexer, permitting analog values from the periphery to be
read.
TEMPERATURE SENSOR
The 908E625 includes an on-chip temperature sensor.
This sensor offers a voltage that is proportional to the actual
chip junction temperature.
VSUP PRESCALER
The VSUP prescaler permits the reading or measurement
of the external supply voltage. The output of this voltage is
VSUP/RATIOVSUP.
The different internal diagnostic analog voltages can be
selected with the ADMUX Register.
ANALOG MULTIPLEXER CONFIGURATION
REGISTER (ADMUX)
SS3, SS2, SS1, and SS0—A/D Input Select Bits
These read/write bits select the input to the ADC in the
microcontroller according to Table 7. Reset clears SS3, SS2,
SS1, and SS0 bits.
Register Name and Address: ADMUX - $07
Bits
7
6
5
4
3
2
1
0
Read
0
SS3
SS2
SS1
SS0
Write
Reset
0
相关PDF资料 |
PDF描述 |
|---|---|
| MM908E624ACEW | IC SWITCH TRIPLE MCU/LIN 54-SOIC |
| 06FMN-BMTTR-A-TB | CONN FMN HSNG 6POS STAG REV SMD |
| 046232104103800+ | CONN FFC/FPC 4POS 1MM R/A SMD |
| 046232106103800 | CONN FFC/FPC 6POS 1MM R/A SMD |
| 046232106103800+ | CONN FFC/FPC 6POS 1MM R/A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。