参数资料
型号: MM908E625ACEK
厂商: Freescale Semiconductor
文件页数: 33/49页
文件大小: 0K
描述: IC HALF-BRIDGE QUAD 54-SOIC
标准包装: 26
应用: 自动镜像控制
核心处理器: HC08
程序存储器类型: 闪存(16 kB)
控制器系列: 908E
RAM 容量: 512 x 8
接口: SCI,SPI
输入/输出数: 13
电源电压: 8 V ~ 18 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 54-BSSOP(0.295",7.50mm 宽)裸露焊盘
包装: 管件
供应商设备封装: 54-SOICW-EP
Analog Integrated Circuit Device Data
Freescale Semiconductor
39
908E625
TYPICAL APPLICATIONS
FACTORY TRIMMING AND CALIBRATION
TYPICAL APPLICATIONS
DEVELOPMENT SUPPORT
As the 908E625 has the MC68HC908EY16 MCU
embedded typically all the development tools available for
the MCU also apply for this device, however due to the fact
of the additional analog die circuitry and the nominal +12 V
supply voltage some additional items have to be considered:
nominal 12 V rather than 5.0 V or 3.0 V supply
high voltage VTST might be applied not only to IRQ pin,
but IRQ_A pin
For a detailed information on the MCU related
development support see the MC68HC908EY16 datasheet -
section development support.
The programming is principally possible at two stages in
the manufacturing process - first on chip level, before the IC
is soldered onto a pcb board and second after the IC is
soldered onto the pcb board.
Chip level programming
On Chip level the easiest way is to only power the MCU
with +5.0 V (see Figure 23) and not to provide the analog
chip with VSUP, in this setup all the analog pin should be left
open (e.g. VSUP[1:3]) and interconnections between MCU
and analog die have to be separated (e.g. IRQ - IRQ_A).
This mode is well described in the MC68HC908EY16
datasheet - section development support.
Figure 23. Normal Monitor Mode Circuit (MCU only)
Of course its also possible to supply the whole system with
Vsup (12 V) instead as described in Figure 24, page 40.
PCB level programming
If the IC is soldered onto the pcb board its typically not
possible to separately power the MCU with +5.0 V, the whole
system has to be powered up providing VSUP (see
MM908E625
RST_A
RST
IRQ_A
IRQ
VSUP[1:3]
GND[1:2]
PTC4/OSC1
PTB3/AD3
PTB4/AD4
PTA0/KBD0
PTA1/KBD1
MAX232
10k
RS232
DB-9
1
3
C1+
C1-
4
5
C2+
C2-
7
8
2
3
5
VCC
GND
16
15
2
V+
V-
6
1F
+
1F
+
1F
+
1F
2
1
3
65
4
74HC125
9.8304MHz CLOCK
+5V
DATA
CLK
+5V
10k
VTST
10
9
T2OUT
R2IN
T2IN
R2OUT
EVDD
VDD
VSS
4.7F
100nF
+5V
VREFL
VDDA
EVSS
VREFH
VSSA
相关PDF资料
PDF描述
MM908E624ACEW IC SWITCH TRIPLE MCU/LIN 54-SOIC
06FMN-BMTTR-A-TB CONN FMN HSNG 6POS STAG REV SMD
046232104103800+ CONN FFC/FPC 4POS 1MM R/A SMD
046232106103800 CONN FFC/FPC 6POS 1MM R/A SMD
046232106103800+ CONN FFC/FPC 6POS 1MM R/A SMD
相关代理商/技术参数
参数描述
MM908E625ACPEK 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
MM908E626 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVDWB 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube