- 您现在的位置：买卖IC网 > PDF目录3914 > MM908E625ACEK (Freescale Semiconductor)IC HALF-BRIDGE QUAD 54-SOIC PDF资料下载
参数资料
| 型号： | MM908E625ACEK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 36/49页 |
| 文件大小： | 0K |
| 描述： | IC HALF-BRIDGE QUAD 54-SOIC |
| 标准包装： | 26 |
| 应用： | 自动镜像控制 |
| 核心处理器： | HC08 |
| 程序存储器类型： | 闪存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 输入/输出数： | 13 |
| 电源电压： | 8 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 54-SOICW-EP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Analog Integrated Circuit Device Data
Freescale Semiconductor
41
908E625
TYPICAL APPLICATIONS
FACTORY TRIMMING AND CALIBRATION
EMC/EMI RECOMMENDATIONS
This paragraph gives some device specific
recommendations to improve EMC/EMI performance.
Further generic design recommendations can be e.g. found
on the Freescale web site www.freescale.com.
VSUP pins (VSUP1:VSUP3)
Its recommended to place a high-quality ceramic
decoupling capacitor close to the VSUP pins to improve
EMC/EMI behavior.
LIN pin
For DPI (Direct Power Injection) and ESD (Electro Static
Discharge) its recommended to place a high quality ceramic
decoupling capacitor near the LIN pin. An additional varistor
will further increase the immunity against ESD. A ferrite in the
LIN line will suppress some of the noise induced.
Voltage regulator output pins (VDD and AGND)
Use a high quality ceramic decoupling capacitor to
stabilize the regulated voltage.
MCU digital supply pins (EVDD and EVSS)
Fast signal transitions on MCU pins place high, short-
duration current demands on the power supply. To prevent
noise problems, take special care to provide power supply
bypassing at the MCU. It is recommended that a high quality
ceramic decoupling capacitor be placed between these pins.
MCU analog supply pins (VREFH, VDDA and VREFL,
VSSA)
To avoid noise on the analog supply pins its important to
take special care on the layout. The MCU digital and analog
supplies should be tied to the same potential via separate
traces and connected to the voltage regulator output.
schematics and layout level and Table 13 indicates
recommended external components and layout
considerations.
Figure 25. EMC/EMI Recommendations
MM908E625
VREFL
VDDA
EVDD
VDD
EVSS
VSS
VSUP1
GND1
VSUP
+
VREFH
VSSA
VSUP2
LIN
C1
C2
D1
C3
C4
C5
L1
V1
VSUP3
GND2
相关PDF资料 |
PDF描述 |
|---|---|
| MM908E624ACEW | IC SWITCH TRIPLE MCU/LIN 54-SOIC |
| 06FMN-BMTTR-A-TB | CONN FMN HSNG 6POS STAG REV SMD |
| 046232104103800+ | CONN FFC/FPC 4POS 1MM R/A SMD |
| 046232106103800 | CONN FFC/FPC 6POS 1MM R/A SMD |
| 046232106103800+ | CONN FFC/FPC 6POS 1MM R/A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。