- 您现在的位置：买卖IC网 > PDF目录3914 > MM908E625ACEK (Freescale Semiconductor)IC HALF-BRIDGE QUAD 54-SOIC PDF资料下载
参数资料
| 型号： | MM908E625ACEK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 19/49页 |
| 文件大小： | 0K |
| 描述： | IC HALF-BRIDGE QUAD 54-SOIC |
| 标准包装： | 26 |
| 应用： | 自动镜像控制 |
| 核心处理器： | HC08 |
| 程序存储器类型： | 闪存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 输入/输出数： | 13 |
| 电源电压： | 8 V ~ 18 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 54-BSSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 54-SOICW-EP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
Analog Integrated Circuit Device Data
26
Freescale Semiconductor
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
POWER OUTPUT REGISTER (POUT)
Current Source Select Bits (CSSEL0:CSSEL1)
These read/write bits select the current source values.
Reset clears the CSSEL0:CSSEL1 bits.
Current Source Enable Bit (CSEN)
This read/write bit enables the current source for PA1.
Reset clears the CSEN bit (Table 9).
HVDD On Bit (HVDDON)
This read/write bit enables HVDD output. Reset clears the
HVDDON bit.
1 = HVDD enabled
0 = HVDD disabled
Lamp Driver On Bit (HS_ON)
This read/write bit enables the Lamp driver. Reset clears
the HS_ON bit.
1 = Lamp driver enabled
0 = Lamp driver disabled
Hall-Effect Sensor Input Pins (H1:H3)
Function
The Hall-effect sensor input pins provide three inputs for
two-pin Hall-effect sensors for detecting stall and position or
reading Hall-effect sensor contact switches. The Hall-effect
sensor input pins are not influenced by the PSON bit in the
System Control Register.
Each pin of the Hall-effect sensor can be enabled by
setting the HxEN bit in the Hall-effect sensor input pin control
register (HACTL). If the pins are enabled, the Hall-effect
sensors are supplied with VSUP voltage and the sense
circuitry is working. An internal clamp circuity limits the supply
voltage to the sensor to 15 V. This sense circuitry monitors
the current to VSS. The result of this sense operation is given
by the HxF flags in the Hall-effect sensor input pin status
register (HASTAT).
The flag is set if the sensed current is higher than IHSCT.
To prevent noise on this flag, a hysteresis is implemented on
these pins.
After switching on the Hall-effect sensor input pins (HxEN
= 1), the Hall-effect sensors need some time to stabilize the
output. In RUN mode the software must wait at least 40
μs
between enabling the Hall-effect sensor and reading the hall
flag.
The Hall-effect sensor input pin works in an dynamic
output voltage range from VSUP down to 2.0 V. Below 2.0 V
the hallflags are not functional anymore. If the output voltage
is below a certain threshold, the Hall-effect sensor input pin
over-current flag (HP_OCF) in the system status register is
set.
Figures 13 through 15 illustrate the connections to the
Hall-effect input sensors.
Register Name and Address: POUT - $0b
Bits
7
6
5
4
3
2
1
0
Read
0
CSSEL1 CSSEL0 CSEN
0(16)
HVDDON HS_ON
Write
Reset
0
Notes
16.
This bit must always be set to 0.
Table 9. PA1 Current Source Enable Bit
CSEN
Current Source Enable
0
Current Source Off
1
Current Source On
相关PDF资料 |
PDF描述 |
|---|---|
| MM908E624ACEW | IC SWITCH TRIPLE MCU/LIN 54-SOIC |
| 06FMN-BMTTR-A-TB | CONN FMN HSNG 6POS STAG REV SMD |
| 046232104103800+ | CONN FFC/FPC 4POS 1MM R/A SMD |
| 046232106103800 | CONN FFC/FPC 6POS 1MM R/A SMD |
| 046232106103800+ | CONN FFC/FPC 6POS 1MM R/A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MM908E625ACPEK | 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MM908E626 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVDWB | 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:马达/运动/点火控制器和驱动器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。